★★★★★
May 26, 2024
Mud flaps
Looks and fits great
Replaces
Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.
This part fits 16 vehicles spanning 2001-2014.
| Year | Make | Model | Description |
|---|---|---|---|
| 2007-2013 | Chevrolet | Avalanche | Chevrolet Avalanche without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2002-2006 | Chevrolet | Avalanche 1500 | Chevrolet Avalanche 1500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2002-2006 | Chevrolet | Avalanche 2500 | Chevrolet Avalanche 2500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2013 | Chevrolet | Silverado 1500 | Chevrolet Silverado 1500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2007 | Chevrolet | Silverado 1500 Classic | Chevrolet Silverado 1500 Classic without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2004 | Chevrolet | Silverado 2500 | Chevrolet Silverado 2500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2013 | Chevrolet | Silverado 2500 HD | Chevrolet Silverado 2500 HD without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2014 | Chevrolet | Silverado 2500 HD | Chevrolet Silverado 2500 HD without Fender Flares with Single Rear Wheels (SRW) Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2007 | Chevrolet | Silverado 2500 HD Classic | Chevrolet Silverado 2500 HD Classic without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2006 | Chevrolet | Silverado 3500 | Chevrolet Silverado 3500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2007 | Chevrolet | Silverado 3500 Classic | Chevrolet Silverado 3500 Classic without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2007-2013 | Chevrolet | Silverado 3500 HD | Chevrolet Silverado 3500 HD without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2014 | Chevrolet | Silverado 3500 HD | Chevrolet Silverado 3500 HD without Fender Flares with Single Rear Wheels (SRW) Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2014 | Chevrolet | Suburban 1500 | Chevrolet Suburban 1500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2013 | Chevrolet | Suburban 2500 | Chevrolet Suburban 2500 without Fender Flares Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| 2001-2014 | Chevrolet | Tahoe | Chevrolet Tahoe Mud Flap 4 Piece Set General Motors OEM GMBMK00005 |
| Brand Label | Part Number |
|---|---|
| DIY Solutions | BAS00510 |
| DIY Solutions | BAS00546 |
| General Motors | 19213393 |
This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.
1 Year Warranty
This item is backed by our 1-year warranty. In the event this item should fail during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
In this video, we're going to show you how to install rear mudflaps for a 2009 Chevy Suburban. If you need this part or other parts for your car or truck, click the link in the description and head over to 1AAuto.com.
We're going to install these mudflaps on this vehicle. It's kind of a universal fit. You could put these on the front. You could put them on the rear. You can put them up high or put them down load.
You want to line them up where you want them to go first. Take a look and see. Maybe get back further behind the vehicle and look and see where they look good. To make it easier, we're going to pull off the rear tires. You can probably do it with the tires on it if you have some small right-angled tools. It'll be a lot easier if we take the tires off.
Pop this center cap off with a flat blade screwdriver. Take a 22mm socket and a breaker bar. Break the lug nuts free. We're going to raise and support the vehicle. Pull the tire off. We're going to have to pull this pushpin out, and we're going to have to pull this bolt out. Before we do that though, we made our marks for how we wanted to line up our mudflap. We want to line that up like that.
Take it, and we're just going to push on the mudflap that's lined up. And it's going to make a mark where that bolt is. I'm going to drill a little hole where that mark is. You could put a little bit of paint, touch-up paint or even Wite-Out on there, and do the same. Line it up and push. Yep, the mark's right there.
Now, we're doing this because it's a universal fit—there's no indications of where your bolts would go. This makes it easier. Right where that mark is, we're going to take a 3/16 drill bit, just going to drill right there. We're going to pull this clip out. Just going to use a trim tool. We sell these at 1AAuto.com.
Pull that out. We're going to use a 7mm socket and a ratchet. Take this bolt out. We're going to reuse that bolt that we just took out. Slide it back in there. Using a 7mm socket and ratchet, tighten that down. To make sure this is lined up, we put the tire back on, because we don't want to install it and have it extremely crooked. At this point, we can line it up. To line it up with the tire, to make sure it looks good.
We're going to drill a hole in between these two holes, because we want three fasteners to hold this down. We want it about an inch in. That's about right. We're going to make our hole a little bigger. We're going to use a 5/16 drill bit, drill the hole a little bigger. Make sure that's lined up with the other one. Can pull this up. We're going to take a felt tip pen. Just make a mark up here in this hole, and make a mark in this hole. There's my mark right there. I'll drill a hole, 3/16 drill bit. Other mark is right here.
Before I install the driver's side completely, because our holes are already marked, I'm going to mimic that on the passenger side. We'll make a mark with the top and the bottom one. The middle one, you're going to have to redo what we just did. At least the top one'll be there. We'll line it up with the other one. Then you can take a pick or a screwdriver or even a felt tip pen if you can get it in there, just make a little make. You can do it right here as well. Then it gives you the gist of where it is. You can drill those two holes, and then make the third one on the vehicle. There's these J nuts, J clips that go on.
We're going to pull back on this inner fender well. We're going to slide these over here. Then one over here as well. There was one already there from the original, so we don't have to install them there. Then we'll take our 7mm bolt, install that. Then we're going to install these Phillips head screws that also come with the kit. Tighten this down with our 7mm socket and ratchet. It's just plastic, so just snug is good. Going to tighten up these Phillips screw bits.
Reinstall our tire. Put the lug nuts back on. All right, good. We're going to torque our wheel in a star pattern to 140 foot pounds. You want to do it in a star pattern so that the wheel gets snug to the rotor without it being warped. All right, we're going to reinstall the cap. There is an index for the valve stem. If you find that, you know that goes right here. Press it on.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Looks and fits great
I like these mudflaps.
okay, having to pull tires to install. was hoping more flexible. Beings they were oem, thought they'd be predrilled..
They're ok Good thing for the Chevy emblem Otherwise they wouldn't be all that
Great product and fit for a 2007 Avalanche. Had no problem with installation.
I installed these two years ago (?) and they have held up to rigorous winter driving, etc. of North Idaho. They immediately helped reduce the road grime on the sides of the Tahoe I put them on. I am very happy with these - and I wish they had similar product for my old '97 Tahoe. They still look as good as new too!
We really like these mud flaps! They were easy to install, there was a You Tube video to view as well.
I like the looks of the mud flaps on the truck. The only thing I didn't like was the difficulty of putting them on. Getting them marked and the holes drilled in both the mud flaps and in the wheel well flanges was difficult and time consuming. I'm pretty good at this sort of thing and it took me most of a day to install them. These are not something a novice should purchase and try to install.
Good quality, easy to install and look good
Easy to install and fit perfectly. Looks great and they were priced right. Great product at a good price.
Yes, this part will fit your vehicle. This is a Genuine original equipment part (OEM) that was factory installed on your vehicle by the manufacturer.
This part is listed to fit the 2002 Chevrolet Avalanche 2500 (without Fender Flares.)
These parts are not compatible with the year of your vehicle. Currently, we do not carry this part for your vehicle. We're always updating our inventory so please check back soon!
Yes, this part will fit your vehicle as long as your vehicle does not have fender flares.
Our parts are exact replacements for your vehicle's OEM parts. As long as your vehicle specifications match up with our listing, these parts will directly fit and function like the originals. These Mud Flaps are rubber.
The GM part # is 19213393.
These will only fit on models without fender flares. We currently do not carry the ones your looking for. Thank you for the inquiry!
We can check and see if this is able to fit for your vehicle. Please provide us with your VIN and we can ensure they are the correct parts. Please let us know if you have any further questions.
These are the factory parts and should come exactly as the original.
Actual Measurements are not listed or available. These parts are GM, OEM parts. As long as your year, make, and model match up with our listing, these parts will directly fit and function like the originals.
