2005 Volvo XC70 4 Piece Engine Mount Set TRQ MTA34693

Hey friends, it's Len here at 1A Auto. Today we're working on our 2004 Volvo XC90. This is the all-wheel drive version, and I'm going to show you how to do an up-top or upper motor mount. Going to be super easy, I can do it. You can do it too.

If you need this or any other part, you can always check us out 1aauto.com. Thanks.

Okay, so one of the first things we have to do after we pop the hood is just take off the cover right here. It comes across the whole valve cover, and then there's another one that comes up along the top right there. Both those need to come out. You're going to use a T25 bit. It looks like a star. That just goes right in here.

You can use a ratchet if you want to. Just show you what the bolt looks like. That's not really the best, not the cleanest, but it's not my fault. That's what it looks like. We'll set this aside, and we're going to remove all the rest of the bolts.

All right, so we'll just get this stuff up and out of here. Just a little cover. There's your timing belt, not that that matters for this job, but ... The ignition coil's under here, there's going to be spark plugs and everything under there.

Here's our mount. Should be fairly easy to do. We've got a bolt that comes through here. We've got two bolts here, and then two bolts on the rearward side. All of it looks fairly easy. What I'm going to do first though is I'm going to get a floor jack and a piece of wood, and I'm going to raise the, or support the engine a little bit, just in case this is holding it up at all.

There's going to be a couple of other motor mounts under here that I'm sure are doing their job well, but just to help them along and just in case, we'll say, we need to be able to move this up or down, to be able to line up the bolt at the end.

I'll grab a floor jack now and we'll move along. Okay, so we've got our jack with our rubber pad. We're going to bring it right in and go right underneath the oil pan there, along an edge. I'm going to go along this edge, because this is the side that I'm going to be working on.

I never like to jack in the center of an oil pan. There we are. I'm just applying very light pressure. I'm not trying to lift the vehicle up off the ground here. Just put that like that. Now we can get started under the hood.

We're just going to take off this rubber boot right here. Pretty simple, slides right off. We'll set that aside. Next, we're going to take out this bolt. There's a nut on the other side. We'll grab our wrench and a ratchet for this side, and we'll remove this bolt.

We're going to use our 18 millimeter on this side, and a 15 millimeter on this side. There's our nut and bolt. This can move around now. The only thing holding in this mount is the four bolts. Let's get those out of there.

We're going to take out these bolts right here. 14 millimeter. If you have access to an air gun, it'll be much quicker than this. For the purpose of this video, I'm just going to do it like this. You can get that one that's hiding all the way in the back there. That one's probably going to be easier with something different. Just because there's something in the way there. There's those. The last one we have is all the way back in this corner right here. This is in the way. I'm going to try and get something a little different. I'll probably just go with a shallow socket and still use my ratchet and see what we can do.

Okay. You have minimal room for this one, but once you get it broken free, should come out fairly easily. There we are. This is the rear left, or driver's side. As you can tell, these are different. It's important to make sure you remember where everything goes. If you're worried about forgetting, you can either draw something or you can just go like this with your new one. Set that aside. I'm going to take out the other two here.

There we are. There we are. We got two more different bolts. Grab our upper mount out of there.

Here we are friends, a quick product comparison for you over here. Right here, we have our original upper mount for our 2004 Volvo XC90 all-wheel drive version, and over here we have our brand new quality 1A Auto part. Both these parts are created equal. You've got your four mounting holes, super important. You got the side over here, brand new rubber bushing. You don't have to worry about it. Even comes with a little extra plate on there for added support.

This is a quality piece. As you could tell, it's the same exact shape. With all that said, I don't see any reason why this wouldn't be a great piece to install onto the vehicle, so I'm going to go ahead and do it. If you need this or any other part, you can always check us out 1aauto.com. Thanks

Okay. It's time to get our brand new quality 1A Auto mount into the vehicle. It's going to be very easy. We're just going to go like this, slide it right along here. It should just want to slide right in there. There it is. Cool. We've got our bolts. I just put mine up, so I'd remember where everything is. Got this one all the way over here. This one went on the passenger side rear, driver's side rear.

I'm not going to tighten any of these down or even bottom them out until all of them are started. The longer of the two for the front goes on the left, or passenger side, I should say. Smaller one. I'll grab this one. That through right there. Okay, everything's started. Let's go ahead and tighten it down.

All right. Now we're going to bottom out these bolts here, the ones that hold the mount to the engine first. I'm going to continue with my 14 millimeter, get that on there. I'm just going to snug this up now.

There we are. All right. Okay. Now, we're going to continue with our torque wrench. We're going to go with 50 Newton meters with our 14 millimeter socket.

Okay. Now, we're going to switch over to our 15 millimeter socket. We're going to tighten up this bolt right here. I'm going to hold the backside of the nut with an 18, and we're going to torque this down to 80 Newton meters. There we are, just check it one more time real quick. Tight. All four of those bolts are tight. We can move ahead to the next step.

We're just going to get our jack out of the way. Okay, let's get some covers back on this. I'm just going to come through like this, right underneath here. Just bring it over. There we are. We've got our other cover. This has little pitons that are going to go into there. Just like that. Bonk bonk.

Cool. I'm just going to grab a few of our bolts up here. We're going to go back to our T25. We're going to get these bolts in here. All right. Down to the nitty gritty here. Get this last one. There we are, tight.

Thanks for watching. Visit 1aauto.com for quality auto parts shipped to your door. The place for DIY auto repair. If you enjoyed this video, please click the subscribe button.

Hey friends, it's Len here at 1A Auto. Today we're working on our 2004 Volvo XC90. This is the all wheel drive version 2.5, and I want to show you something very basic. We're going to be removing the engine mounts. These are the lower mounts. They're easy to get to. I can do it. You can do it too. As always, if you need this or any other part, you can always check us out at 1aauto.com. Thanks.

All right, so one of the first things we're going to do is get this bolt out of here. To do that, I'm going to use a 15 on this side, I'm going to use an 18 millimeter wrench on this side, which is the nutted side. You can use your hand ratchet or airgun, whatever you've got access to. Just try to get it in there. I'm going to grab a short extension real quick. They came through from the passenger side to the driver's side. Set that up there. This can move around, clear to move on to the next step.

So I'm going to use my 18 millimeter wrench. I'm going to go right on this nut under here. Use my 17 millimeter up top here. Went up to down, or straight up and down. Do the same to this side. Let's see if we can get this in under here. We'll get this out of the way. All right, so there's a stud that comes up and then there's a nut on the top there. You can remove that right there. It's pretty easy to get to. We'll just grab an extension and a swivel socket and we'll be able to get to it easy peasy.

Okay, so I've got my 15 millimeters swivel down there, a nice long extension and I have my air gun. You can use a ratchet. Anytime I'm using air gun, you can also use a ratchet. That's the nut that goes on top of that. Now we can move ahead to the next step. All right, so we're going to take these out, 10 millimeter. We'll get this out of the way so we can get our mount down in there. Oops. Both those look the same. Set them aside, grab this. This just slides into the air filter box like that. You just kind of go up and pull it out. Set this aside.

We're going to take our mount, just bring it right down in. We've got plenty of room at this point. I'm just going to set it down in here so that way there when I'm underneath there, and I finally get the other mount out, the original, I'll be able to just swap them. And then once we bring the vehicle back down, I'll grab the old one out.

All right, so we're just going to apply a little bit of pressure on the oil pan here. I'm going to come right along the edge and we're not going to try to lift it up too much because of course the mount is still attached and everything. But we're just going to apply a gentle amount of pressure, just like that. So it's holding it. Awesome. Now we can move ahead to the next step. So I'm going to take out these two bolts right here and that's going to make it so this thing can come loose. Both those are the same, can set these aside. At this point, this can move around.

So now we're going to go right up in this hole right here. There was a bolt that has a 14 millimeter head. I'm just going to hold that mount so it can't spin too much on us. Bolt should be ready to come out. All right, so we'll get the mount moving around a little bit. That's if I can get that bolt. There it is. So there's our little bolt, just like that. Set this aside. So now we're just going to jack this up until we can get this mount out of here. So close. All right, so the hardest part is just getting it jacked up high enough to be able to get the mount out of the way. We're just going to set this one right up out of the way and then I'm going to grab my new one and we'll be able to move along.

Okay, so we just need to make sure that we have that triangle right there located up inside the slot where it belongs, right there. Once you get it in, they shouldn't want to spin around anymore. Now we're just going to take this, lower down the engine a little bit. Make sure the old one's out of the way enough. Can see the hole, put the mount right through my hole here, so I'm just going to get that bolt started. Yep. Now that it's definitely started, I'm going to continue to lower until the engine is resting right on the mount and I don't have to hold it anymore. Make sure that other mount's still moving around, it's not stuck on anything. Perfect. All right, we can snug this up and then we'll torque it down. Make sure this is tight. It's definitely tight. All right, now I'll move over here. Get these bolts in.

I'm just going to go ahead and snug these up. Tight. All right, so we're just going to come back out front here, grab our mount under there, set this aside and we can continue. So we've got our nut and that's going to go right on the stud on the mount up there. Got that started on there. Grab our extension with our swivel socket. Just like that. Now I'm going to grab my gun and we'll snug it up. Just lock it on there. That's tight. Let's move along.

Okay, so we've got our intake tube here. We've got our squared end, that's going to go inside the air filter housing box down on the bottom down there. Just weasel it underneath these wires and such, feel around, the hole for this is pretty close to the front of the box. It's on the side, but it's very close to the front like right about here. We'll be able to line up these holes now. Two screws, I'm going to tighten those up. Tight.

All right, so it's time to get this bar back in here. It's going to come right up and over like this. Line up the hole here, get this one so it's sitting up where it's going to go. Everybody looks happy. Pick whichever bolt you want to start with. These go down and through. Just like that. Get your nut for the bottom there. It's definitely started. Bonk, bonk. Just going to get my hand down here. There we are. All right, everybody started in, let's go ahead and snug them down.

We're going to use our 18 millimeter wrench down on that bottom nut, 17 on top. Same for this one. Now we're going to do this one. All right. There we are. Easy peasy. All right, so we're going to torque this down. We're going to get our 18 on the bottom there, our 17 on the top right here. We're going to tighten this down to 85 Newton meters. There we are. One more time. Okay. Just come over here, same thing, 85. We're going to go 85, there we are. Just try to get me wrench off of here real quick. Tighten this down to 85 as well, there we are. So torqued, torqued, torqued.

Thanks for watching. Visit 1aauto.com, your place for DIY auto repairs, for great parts, great service, and more content.

Hey friends, it's Lynn here at 1AAuto. Today we're working on our 2004 Volvo XC 90 all wheel drive version and I'm going to be replacing the forward lower torque shift mount. It's going to be very simple. I can do it, you can do it too. And as always if you need any parts you can always check us out at 1AAuto.com. Thanks.

All right. So one of the first things we're going to do is get this bolt out of here. To do that, I'm going to use a 15 on this side. I'm going to use an 18 millimeter wrench on this side which is the netted side. You can use your hand ratchet or air gun, whatever you've got access to. Just try to get it in there. I'm going to grab a short extension real quick. That came through from the passenger's side to the driver's side. Set that up there. This can move around. Clear to move on to the next step.

So I'm going to use my 18 millimeter wrench. I'm going to go right on this nut under here. Here's my 17 millimeter up top here. Point up to down or straight up and down. Do the same to this side. See if we can get this in under here. We'll get this out of the way. All right. So, there's a stud that comes up and then there's a nut on the top there. You can remove that right there. It's pretty easy to get to. We'll just grab an extension and a swivel socket and we'll be able to get to it easy peasy. Okay. So, I've got my 15 millimeter swivel down there, a nice long extension and I have my air gun. You can use a ratchet. Anytime I'm using an air gun you can also use a ratchet. That's the nut that goes on top of that. Now we can move ahead to the next step.

All right. So we're going to take these out, 10 millimeter. We'll get this out of the way so we can get our mount down in there. Both those look the same. Set them aside, grab this. This just slides into the air filter box like that. You just go up and pull it out. Set this aside. We're going to take our mount, just bring it right down in. We've got plenty of room at this point. I'm just going to set it down in here so that way there when I'm underneath there and I finally get the other mount out, the original, I'll be able to just swap them. And then, once we bring the vehicle back down I'll grab the old one out.

All right. So, we're just going to apply a little bit of pressure on the oil pan here. I'm going to come right along the edge. And we're not going to try to lift it up too much because of course the mounts still attached and everything. But we're just going to apply a gentle amount of pressure just like that so it's holding it. Awesome. Now we can move ahead to the next step. So I'm going to take out these two bolts right here and that's going to make it so this thing can come loose. Both those are the same, you can set these aside. At this point this can move around. So now we're going to take these out, use my 18 millimeter. There's one, there's two, and here's our mount.

So here we are friends, a quick product comparison for you. Over here we have our original torque shift mount out of our 2004 Volvo XC 90 all wheel drive version and over here we have our brand new quality 1AAuto part. Both these parts are created equal, they're the same length which is very important. You have the same mounting areas. Also, super important. Everything to say about it's really very visible. Everything's brand new. You've got brand new rubber bushings in there obviously, new bolts. It comes with everything you need to go ahead and install it. With that said I don't see any reason why I wouldn't want to install this into the vehicle so I'm going to go ahead and do it. As always, if you need this or any other part you can always check us out at 1AAuto.com. Thanks.

All right. So, we're going to take our mount. We're going to bring these studs through these holes. Here we are. Bring this one up over here. We're going to get these bolts. We'll get those started as well and then we'll go ahead and button this down. We've got our two bolts. You don't need to use thread locker on these by the way. Some people might say you should and I guess that would be your prerogative. I'm not going to get mad at you. I'm just letting you know you do not need to. You do you booboo.

All right. Now that we've got all these started we can go ahead and start snugging things up. Safety glasses. I want to try to line this up with the way that it was originally. Okay, that one's tight, tight, tight. Let's move along. I'm just going to go ahead and snug these up. Tight. So we've got our nut and that's going to go right on the stud on the mount up there. Get that started on there. Grab our extension with our swivel socket just like that. Now I'm going to grab my gun and we'll snug it up. Just lock it on there. That's tight. Let's move along.

Okay, so we've got our intake tube here, we've got our squared end. That's going to go inside the air filter housing box down in the bottom down there. Squeeze the lid underneath these wires and such. Feel around. The hole for this is pretty close to the front of the box. It's on the side but it's very close to the front like right about here. We'll be able to line up these holes now. Screws, tighten those up. Tight.

All right. So it's time to get this bar back in here. It's going to come right up and over like this. Line up the hole here, get this one so it's sitting up where it's going to go. Everybody looks happy. Pick whichever bolt you want to start with. These go down and through just like that. Get your nut for the bottom there. It's definitely started. Put the band down here. There we are. All right, everybody started in. Let's go ahead and snug them down.

We're going to use our 18 millimeter wrench down on that bottom nut. 17 on top. Same for this one. Now we're going to do this one. All right. There we are. Easy peasy. All right, so we're going to torque this down. We're going to get our 18 on the bottom there, our 17 on the top right here. We're going to tighten this down to 85 Newton meters. There we are. One more time. Okay. Come over here, same thing, 85. We're going to go 85. There we are. Get my wrench off of here real quick. Tighten this down to 85 as well. There we are. So torqued, torqued, torqued.

Thanks for watching. Visit 1AAuto.com your place for DIY auto repairs for great parts, great service, and more content.