Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Fog Light Assemblies 2011-17 Toyota Camry
Created on:
Tools used
Phillips Head Screwdriver
10mm Socket
Ratchet
1. Removing the Splash Shield
Remove the 10mm bolts from the splashshield
Lower the splashshield
2. Removing the Fog Light Assembly
Remove the Phillips screw from the fog light
Remove the fog light
3. Installing the Fog Light Assembly
Insert the fog light assembly into place
Tighten the Phillips screw to the fog light
4. Installing the Splash Shield
Insert the splash shield into place
Tighten the 10mm bolts to the splash shield
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hi, everyone. Sue here from 1A Auto, and today we have a 2013 Camry in the shop and I'm going to show you how to change the fog light assembly that is from 1A Auto. If you need this part or any other part for your car, click on the link below and head over to 1aauto.com.
So we're going to take the undercarriage splash shield down that's attached to the bumper with a 10 millimeter socket. We're just going to go from one side. Walk our way over to the other.
To remove the fog light, now we can put our hand up in here in the Phillips screw, that one mounting screw. I'm using a stubby screwdriver. And you back that screw out. Then you grab the new fog light and pull it towards you this way under the hinge part. Layer it out.
Here we have our brand new fog light assembly from 1A Auto. This is for a '13 Camry and here's the factory one we just took out of the bumper. You can see they have the same four mounting spots. Turn ours around. It comes with an adjuster, just like that one, and we also supply the bulb. And a vent for any moisture to come out. If you need this part or any other part for your car, click on the link below and head over to 1aauto.com.
Now we're going to put the new fog light up in. Pull down a little bit and just screw it underneath. You're going to put those two tabs in on the inner edge. Line those up. You're going to take these two tabs and line up with these two holes, eyelet holes, and just fog light right up in place. Now I'm going to put the Phillips screw back in the mounting hole. Snug that right in. Put the shield part up underneath the bumper cover and line up the actual mounting screws all the way around.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
TY877-B000L
In Stock
Product Reviews
Loading reviews
4.67/ 5.03
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
1
0
0
0
Review: Purchase of Toyota Venza Fog Lamp (Driver Side)
N
June 30, 2017
About the product:
After market. Fit the fog lamp slot perfectly. Works well. No issues. The product came with its own bulb and this helped me save the older working bulb, for future use.
Product Installation:
Super easy in the Venza. Took about 15 minutes to replace the old one.
Buying and receiving from 1A Auto:
Ordered online. Did not receive the Product on the date specified. After checking with local postal agency, sent an email to 1A Auto regarding non-delivery. They shipped another piece which I received. The packaging was good and the product was clean and not damaged. Except for the non-delivery on the first instance leading to more wait time), I did not face any other issues with 1A Auto.
1A Auto is a good online shop to consider when ordering auto parts.
Perfect fit
Douglas
December 6, 2019
Went right in no problems. 15 min job. As with other products purchased from 1aauto good quality. Love the install videos!
Good product
R
December 28, 2019
Product was as described........ works great!
Customer Q&A
How to install the fog light?May 18, 2016
Philip H
10
Really simple. Disconnect bulb then remove one mounting screw from fog light assembly and assembly comes right out. Reverse process to install new fog light.
May 18, 2016
Joshua H
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.