Replaces
Part Details
About TRQ:
TRQ is a trusted brand dedicated to making every repair a success story by combining premium parts with easy installation. Each TRQ part is engineered by a team of automotive experts to meet or exceed OEM standards, delivering enhanced performance and maximum longevity. With rigorous in-house testing, the brand ensures superior fit and function across every product line. TRQ also provides customers with best-in-class, step-by-step installation videos—so you can complete repairs with confidence, whether you're a first-time DIYer or an industry professional.
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hey, I'm Brian, I'm here to give you guys a little tutorial on some window regulators. The specific design is the scissor design. We actually get a lot of calls on these products here and the common question is: The part I received seems different than the part in my vehicle.
The scissor design actually has a flip design and we're actually going to show you how to fix this here. The most common thing that you want to do, or the first step you want to do is lay the parts out side by side. Try not to match them up in the car because this can get confusing. Take it out, lay them side by side, and what you actually see here is a same exact part for the same model vehicle in the same door. As the appearance shows here, they seem to be mirrored.
If you look down at the bottom here, we have the power window motor. This is the piece that is actually powered to lift and lower your glass. The next section down here is . you actually have your gear drive. Here's your mounting plates on both. As you can see, it's identical. You have your tension spring here. If you notice on the upper section here, it's kind of reversed. You're going to think normally, I get the wrong side door. You're going to give us a call and you want to express that to one of our customer service reps. I'm going to show you how to fix this.
Basically, pick this up by the base and you want to scissor or flip. This is how you're going to fix the issue. It's going to actually match the component as shown there. You can now see that both of these components here are the same part and you're ready for installation.
You should be good to go. Click on Subscribe or check us out at 1AAuto.com. We'd be more than happy to have you join on board and join the 1AAuto team.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green, I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this, to show you the correct way to install parts from 1aauto.com. The right parts, installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video we're going to replace the front window regulator on this 2004 Dodge Ram, same for any 02' to 08' 1500, as well as the 09' 25 and 3500's. Tools you'll need are a T40 Torx driver, Phillips screwdriver, flat blade screwdriver, and 10mm socket and ratchet with an extension.
To remove your front door panel, you're going to start by removing a T40 Torx screw and hold your handle on, right there. Then you're going to remove four Phillips screws, one there, one up here, and two down on the lower part of your door panel. There's my T40 Torx driver. We're going to speed it up here, take that T30 screw out, and then your handle comes off. Then I'm going to start with the Phillips screw drivers, take those two off. Then slightly take my jacket off so you can see my 1A Auto sweatshirt, and remove the two lower Phillips screws.
Now I use a regular screwdriver to carefully pry up on your switch plate here. Then pull it up. Both of these connectors, they have a little button right here. Press the button and work the connector to the switch; same thing here. There's a button right there. Now you're just going to life the door panel up over the lock here, take it off. You're going to want to use a 10mm wrench or a socket and ratchet. There's a bolt here, there's also a bolt there but it's missing. Not sure of this door maybe has been taken apart before. Then there's a little clip right here that you either push down with your hand. Just pull it down, and then you're going to pull this rod right out.
Then you want to carefully pull your water shield down. Pull your water shield back. Your regulator is held on by four bolts here; one, two, three, and four. There's two bolts that hold a bracket here, and then there's two bolts that hold the window. I want to demonstrate to you how do you get it apart if it's stuck in the up position. You would remove these two nuts right here. Now we'll just speed it up a little bit, as I'm removing those two 10mm nuts. I'm reaching behind, right here is my lead, and I'm just reaching in there. There's a tab on top, pulling that lead that. I'm going to remove these four bolts over here. Now we'll just fast-forward through me removing those four bolts.
Now I can bring my window down. With my window down some I can see there's that 10mm nut there, and there's a 10mm nut there. Those hook the window to the window regulator. Once I loosen them you can see that I would slide it over to the right, which allows the track to go out around that nut. I'm going to tape the window right there, so id doesn't fall down. Now I've got my hand stuck down in the bottom here. I'm holding up the regulator by the motor. I'm going to flip it off the track up here. I'm going to reach up in, carefully, and pull it from the door and bring it down. I'm going to push it towards the outside of the door.
Here's my original regulator, and new regulator from 1A Auto. You can see everything is pretty much the same. It's actually just in a different position here. It has the cut outs for the window bolts right there and everything. The actual lead is the same. Ours does have this little longer lead, actually makes it a little easier to get together. On the other side, it has the balance spring. This bracket has the bolts and everything.
Before you go to install your regulator, what I like to do, is get my window all the way in the up position. I'm going to put my new regulator in. I'm going to thread this bolt three quarters of the way in, and this one three quarters of the way in. Put the regulator down in, reach in with my other hand. Grab the - Now with my right hand I have the motor. There's that bolt and my other bolt. My two bolts here are in. Let's see here, push that one up through and put a nut on there, just slightly. Then twist it a little. Push it off, I just need to push it. Push the regulator back, so I have a little clearance here. Get those on. Now I'm going to start that bolt and that bolt. I'm going to tighten these up.
Now I'm going to reach under here, feel my lead coming down. I got my connector from the door. I'm going to bring my lead our around this harness, just so I know it stays out of the way. No I can turn my key on, run my regulator up so I can see my track. Now I can see my track right through there. Then right there, except I'm going to run it up just a little more. Tape off my window. Slowly slide my window down. Got that one on, and that one is on.
Now basically you reach in there, and you might have to rotate the window a little bit; move it up and down a little bit, so you can slide the track all the way onto the studs. Just speed it up a little bit. Tighten up those bolts that hold the window. Tighten up the nuts on that track. Run the window up and down to just check it. Make sure all the other bolts are tight. Put our water shield back on. Reinstall our handle, and make sure that that rod and clip are in place. Then you can put your door panel back on.
We are going to continue the fast motion here, as we put the door panel back on. If you want to see this in regular speed, just check out our video Dodge Ram door panel installation and removal. Probably you can get enough just by watching here. Put that door panel on, put it in place, slide it down onto its clips. The four Phillips screwdrivers, I'm sorry, the four Phillips screws install them. Put your switch plate back in place and press it down into place. Then reinstall all your handle with your T3o Torx but. Then put your little lock bezel back on.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.
WRA51859
