Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Install Tip: You may be required to reset the vehicle computer after installation of this part.
Returns: Parts with electrical components cannot be returned once installed.
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Mass Airflow Sensor 2003-13 Mazda 6
Created on:
Tools used
Phillips Head Screwdriver
1. Removing the Mass Airflow Sensor
Disconnect the wiring harness
Remove the Phillips screws from the mass airflow sensor
Pull the sensor up and out
2. Installing the Mass Airflow Sensor
Insert the mass airflow sensor into place
Tighten the Phillips screws to the sensor
Connect the wiring harness
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Hi, my name's Sue from 1Aauto.com, and today we're going to be putting a mass airflow sensor in an 07 Mazda 6 Sedan 2.3-liter. To start, we're going to open the hood, and that's the lever mounted on the driver-side knee panel that has a picture of the hood. Pull on the cable, and then go out and release the safety latch.
So now I'm going to release the hood safety latch that's mounted right above the symbol of the car. Bring it over to the driver's side. Lift up the hood. The hood prop rod is right here in the front. It goes right into the slot that's marked with an arrow. So to replace the mass airflow sensor, we're going to disconnect the sensor itself first, from the harness and it's a push tab, push down on it, and squeeze it out.
I like to make sure there's no burnt connectors that can cause a code or running condition also. Now we have two mounting screws. You just need a Phillips screwdriver. I'm going to dismount them. You just give it a firm twist and lift up. There's an O-ring right here, that keeps it nice and sealed.
Here we have a mass airflow sensor from 1aauto.com, and the factory sensor I just took out of my Mazda 6 2007. They look like they're from the same manufacturer.
So then we have our new mass airflow sensor, has a new O-ring, as you can see it's not crushed like the other one was.
So I'm just going to place that right in here. I wouldn't put any silicone or lubricant on this, because on a mass airflow sensor that is part of the reader right there. That's the air temp sensor on it, and the mass airflow sensor is inside. They pick up on dirt or oil, and it throws the sensor off, the reading, so a nice dry seal's fine because it's plastic, it's not metal.
So I'm just going to mount it down. You cannot mount it the wrong way as you can see. If I went like this, the holes don't line up, it's nice and easy, self-explanatory, press down. I felt it move right in. Now I'm going to remount it with the two Phillips head screws. I'm not going to snug that down tight yet until both are in. Now I'm going to reinstall the connector. Make sure that that orange seal is still on there. That's the moisture barrier, water seal. And I'm just going to wind it right up, click it on. There you go, now you're ready to go.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
EMS00612
In Stock
Product Reviews
Loading reviews
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Mazda is a registered trademark of Mazda Motor Corporation. 1A Auto is not affiliated with or sponsored by Mazda or Mazda Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.