2016 Ram 5500 Truck Windshield Washer Fluid Level Sensor Mopar 05152029AB

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the fluid level sensor. This is a 2008 Dodge Ram, but this sensor and this process is the same for many different Dodge and Chrysler vehicles. You'll need a new fluid level sensor from 1AAuto.com, drain bucket, flat blade screwdriver, and washer fluid.

Open your hood and locate your coolant expansion and washer reservoir bottles. Remove the feed tube on the bottom of your washer pump. Make sure you have a drain bucket to catch what comes out.

Disconnect the safety on your washer level sensor connector, and remove the connector from the sensor. Your sensor just needs to get wiggled out of the back of the reservoir.

Here's the sensor we removed from the vehicle. You just remove the grommet if it came out with it. Put it on the new one, the new part from 1AAuto, exactly like the original. It's going to install just like it.

Remove the grommet from your sensor and install into the hole in the back of your reservoir. Then install your new sensor. Reconnect the connector, install the safety, reattach your washer hose, and refill your washer fluid.

Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.

In this video, we are going to be removing and replacing the washer fluid level sensor in a 2016 Ram 1500 pickup. If you need this part or other parts for your vehicle, click the link in the description and head over to 1AAuto.com.

Going to open the hood red under your steering wheel. This little lever pops the hood. The hood safety latch is right here, going to pull it to the left, pull up. We're going to pull this panel off. There's some clips. You're going to use a clip tool to get underneath here. There's one over here too. It's easier if you go under it and pry up on it. You could go underneath the clip and pry, but sometimes you break the clip, so we'll just go underneath it, pry up. Pull that up. Then, we just pull this off and pull it out of the way.

We're going to take these four bolts out right here. They're 10 millimeters. Use 10-millimeter socket and a ratchet.

Down here, there's a clip that holds it in. I'm going to use a flat blade screwdriver. These clips sometimes break, so just be careful. Just pop it out like that. There's another clip further down. You can't see it. Then, on the other side is the same clip right there. Pull that out.

Then, we're going to use some trim tools. We actually sell these at 1AAuto.com. I'm going to go under here. You want to be careful not to scratch the paint, but there is some retainers under here. I'll show you these better once the grill is out. Right there. Hold up. Then, we're going to grab on the grill and pull forward, release that one. There's one over here as well. Then, there's also one in the middle. That releases. Then, there's one more in the middle, and the whole grille comes up.

All right, to get this pump out, we're going to remove this wire over here, pull that out. We'll disconnect connector right here. Use a flat blade tool. Pry that. Then, you can pull up on the connector right there. Just put the tool in there and that'll move the lock, or you can use your finger. Then, we'll pull this hose. When we pull this hose off, the washer fluid's going to go all over the place, so have a bucket underneath, or if your system's empty, it's not going to matter. Going to use a 90-degree pick, stick it in underneath the hose. Just work it around a little bit. That'll break the seal. I should be able to push it off. Pull that out of the way.

All right. Now, we're going take this bolt out. It's a 10 millimeter. We're going to use a socket and a ratchet. Next, we have to pull this bolt out down here, so I'm going to use a universal, an extension, a 10 millimeter and a ratchet. Try to get this out without dropping it.

All right, next, we're going to pull straight up, release these little locks that were locked in. I'm going to pull out. There's some wires in the back that are connected, so connection right here. This little red lock on the connector, I'm going to use a straight blade screwdriver and pull up on the lock. Now we can push it down with our fingers. Then we can pull it right out.

Take a straight blade screwdriver to get under this level sensor. I'm just going to pry up a little bit, going around, being careful not to break it. You can pull it out just like that. Here's your rubber grommet. Pull that out.

Reinstall. Push that in. You can use a small screwdriver to get it in. The flat part is going to go at the top. You're going to push it straight down. That's in. We're going to reconnect our washer level sensor in the back. Then, push down on the red lock. Then, this wiring harness gets pushed in on the back here. These two lock tabs are going to go, slip down there.

Take our top, 10-millimeter bolt, start that. Before we tighten that, we can put our bottom one in. Get the bottom one started. Once that one's in, we can snug this one down. Tighten that down. We can go to the top one, tighten the top one up. Snug that up. Remember it's plastic, so you don't want it too tight.

Next, we can take our hose and our wiring harness, slip it over here. We're going to put the hose on the pump first. It's a little tricky to get in here, but push it on. Push it down onto the pump. Probably want to go a little bit further. That looks good right there. Push the hose in this groove here. Then, we'll connect this electrical connector for the pump. Then, push these wire into that groove.

We're going to put this on. Keep in mind to keep this up, that little rubber piece. Line those up. you're going to line these lock tabs with those holes. Get it lined up, up top. You can push in the bottom. It should lock in.

We have these 4, 10-millimeter bolts that are going back in. These ones are going to go into the plastic. The ones that look more aggressive than the tighter threads, those will go right there. Then, these other ones are going to go in the center into the metal frame. We'll start all those first. We'll tighten these down with our 10-millimeter socket, extension, and ratchet. Tighten it snug, and the last one.

We're going to put this cover on. Get all the holes lined up to the push pins. Push those in, and then right there.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Hi. I'm Mike from 1A Auto and I’m here to talk to you about fluid level sensors. Here is a fluid level sensor that we removed from this 2008 Dodge Ram behind us.

They go into a washer bottle and the prongs basically sense, whether or not there is enough fluid level in there. When they can't, they send a little signal out, and it lights up a light on your dash.

These sensors, they can wear out over time and not work, but basically, at 1A Auto, this particular version is a Mopar part. Mopar is the original equipment brand of Dodge and Chrysler. When you see this symbol, actually, the people that made the part in this box or the people that made the part for Dodge, Plymouth, or Chrysler. As you would expect, it's the exact same part. From the sensor we removed from the vehicle, you just remove the grommet if it came out with it. Put it on the new one. The new part from 1A Auto is exactly like the original. It's going to install just like it.