Replaces
Part Details
Specifications
Product Features
TRQ CV (constant velocity) drive axles are manufactured using premium raw materials designed to restore original performance. TRQ CV drive axles are new, so there is no core charge with your TRQ purchase. TRQ-designed drive axles utilize neoprene boots, moly grease, stainless steel clamps, and heat-treated ball tracks to ensure extended service life. Each TRQ axle is application-specific so each spline and thread will mate properly for a seamless fit. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems. If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
With the vehicle on the ground, I'm going to use a 19 millimeter socket and a breaker bar to loosen the lug nuts. With the lug nuts loosened, now we're going to raise and support the vehicle. With the lug nuts loosened, I should be able to use just the socket and finish removing them. Then I can take the wheel off. All right, last lug nut removed, I can take the wheel off.
You need to remove the axle nut. It's been staked in place. Going to take an old flathead screwdriver that fits in the opening. I'm just going to tap it in to bend that metal out. If you do have someone that can help you, they can get inside the car and step on the brake and hold this to keep it from spinning while you remove it. Or you can take your wheel, pop the cap out, reinstall the wheel, lower the car back down, and then with the vehicle on the ground, we can loosen the axle nut through the opening on the wheel.
I'm just going to install the lug nuts. These don't have to be torqued, just loosely tightened down so the wheel doesn't move, because we're only going to put the car down on the ground. We're not going to drive it anywhere. Lower the vehicle back down to the ground. Alright, with the vehicle on the ground, I'm going to use this 32 millimeter socket and a breaker bar, and we will loosen the axle nut. See how loose it is.
All right, now I can put the car back up in the air and take the wheel off. With this axle nut loosened, I'm going to remove the wheel again. You can loosen the bolts and the two nuts and the studs holding the lower ball joints and control arm. Once these are loose, you can swing the whole knuckle brake suspension assembly out and away from the axle. This will allow us to remove it from the transmission.
This is a 17 millimeter socket and a breaker bar I'm going to use to loosen these. Get them all loosened first. Now I'm going to take a pry bar and just pry the lower ball joint apart from the control arm. Pop it out like that. Make sure this nut is loosened up. I want to make sure that this axle will come out of the hub assembly, so I just take a dead blow mallet and just tap it. It's going to move pretty freely.
We got lucky with this one. Just tap it some more, but it should come free. That's going to come right out. I'm going to grab hold of the knuckle assembly, and the whole suspension assembly, put one hand on the axle and just guide this off. Just push it out like that. Lay the axle aside over here. We're going to put a drain pan in place because when I pop this axle shaft out of the transmission, some transmission fluid may leak out. I'm going use a pry bar to reach up underneath the joint. You don't want to pull on the joint; you want to pry on it carefully over here. Work that in. There it is. I'm going to try to pull it out as straight as possible not to damage the transmission seal. Let's see here. There we have our axle.
Here's the original one from our vehicle, and a brand new one from 1AAuto.com. No core charge on this. It’s similar in design. Same style splines and snap ring. It has the same outer splines and same style locking nut. This should fit great and work great in our vehicle.
Take our new axle shaft and guide it up into the opening of the transmission. Bend it a little bit. Guide it in, and do not nick the seal. You can kind of turn it in a little bit. It will find the splines and slide in. Get that in place. You need to seat it in the transmission so it feels like it's caught on the splines. Yup, it's caught on the splines. I've got the axle nut out here. Take our dead blow mallet, give it some taps, and that will drive into the transmission. Then I can see it's seated itself.
I'm just going to grab our suspension assembly, just pull it aside. Lay that down for now. Take this axle nut off now. Keep it nearby. Take our suspension assembly, push it out. Take our axle, line it up. It should slide right in there. Spin this and get the splines to line up. There it is. Take out our axle nut and just capture it so it doesn't back out. Then I need to reinstall the ball joint into the lower control arm. Push this arm down, pull this over. I'm just going to use a pry bar to get in here, pry this down. Get those in place. I have to move it a little bit. Okay, caught. Tighten down.
Use a ratchet just to bring these down snug. There is an order to torque these down. The torque will be 43 foot pounds. You'll start with the front nut, the rear nut, and then the bolt. Take our axle socket and just snug this axle nut down. I'm going to spin this so this is facing up because I'm going to put the wheel on it, I'm going to torque it, and then I want to be able to punch it down where I can reach it.
Reinstall the wheel. Use the socket, snug these up. Put the vehicle back down. I'm going to torque the lug nuts first to 80 foot pounds using a cross pattern. Now we've got a torque wrench and our 32 millimeter socket. The torque wrench is set to 134 foot pounds to torque the axle nut. Now with the axle nut torqued, we need to stake it in place. I'm going to take a punch and a hammer and fold it into that little opening in the axle shaft. You don't have to go too crazy. Finally, reinstall your center cap by just pushing it in.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
CSA82158
