WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Window Regulator 2002-06 GMC Envoy XL
How to Replace Window Regulator 2002-06 GMC Envoy XL
Created on:
Tools used
Razor Blade / Gasket Scraper
Flat Blade Screwdriver
Putty Knife
7mm Socket
10mm Socket
Ratchet
1. Removing the Door Panel
Pry up the door pull trim piece with a flat blade screwdriver
Remove the two 7mm bolts from the door pill
Pry out the door panel clips with a putty knife
Pull the door handle out of the door panel
Lift the door panel up and off
Push the window switch out of the door panel from behind
Disconnect the window switch wiring harness
Peel off the water shield, using a razor blade if necessary
2. Removing the Window Regulator
Lower the window to access the window clamp nuts
Disconnect the window motor wiring harness
Loosen the two 10mm nuts from the window clamp
Pull the window out of its clamp
Unclip the regulator cables from the door
Remove the lower two 10mm bolts from the regulator
Loosen the top ten mm bolt from the regulator
Pull the window regulator out of the door
3. Installing the New Window Regulator
Remove the top 10mm bolt from the old regulator
Insert the 10mm bolt into the new regulator
Hang the new regulator in place by the bolt
Insert the lower two 10mm bolts into the regulator
Tighten all three 10mm bolts
Clip the regulator cables into the door
Loosen the 10mm window clamp nuts
Connect the window motor wiring harness
Lower the window onto its clamps
Tighten the 10mm window clamp nuts
Put the ignition in accessory mode
Connect the window switch wiring harness
Test the window with the switch
Disconnect the window switch wiring harness
Turn the ignition off
4. Reinstalling the Door Panel
Put the water shield into place
Push the door panel shield onto the door panel
Thread the wiring harness through the window switch cavity
Lift the door panel into place
Push in the door panel clips
Connect the window switch wiring harness
Push the window switch into the door
Insert the two 7mm bolts into the door pull
Push in the door pull trim piece
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a rear window regulator on this 2003 GMC Envoy XL. It's the same part and similar process on the regular Envoys from 2002 to 2009. The items you'll need are a new rear window regulator from 1AAuto.com, flat blade screw driver, a 7mm and 10mm socket and ratchet, and a putty knife.
Start off by prying up this little cover with a flat blade screw driver. Then remove those two 7mm bolts. Stick a putty knife behind the door panel and slide it down until you find the first clip and pry out and reach in behind the door panel and just pull out around each clip. Once you remove each of those clips, you can pull the door handle back. Then just push this switch from underneath. It comes up and out. Then push the tab on the harness and disconnect it. You could technically do this before removing the door panel, but you're more likely to scratch up your door panel if you do that. Remove your water shield. Having a razor blade can help because you can just cut at the adhesive, but you can also just pull it free.
This is a cable activated regulator, and a lot of times when they break, what you'll be able to do, you'll hear a popping and grinding noise, and then your window will actually move up and down. So, once you get the door panel off, you'll want to move it to this position where you can get at this 10mm nut and this 10mm nut, and you're going to loosen those. Before we do that, we'll just take a screw driver and push on this tab here and push the connection out. Pull the window up and out of those clamps. Then push the tabs on this clip and push it through the door. Then remove these two 10mm bolts and loosen this top one. Tilt your window regulator and then lift it up and unhook it and pull it down and out of the door.
On the left is the old regulator. On the right is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Remove that top bolt from your old regulator and thread it into your new one just loosely so that you can hang it up in the door. Take your new window regulator, feed it up into the door, push that bolt through the top and hang the regulator and then just line it up and replace those other two bolts. We'll fast forward as Mike does this and tightens them both up. Push this clip back into the door, loosen up these window clamps, reconnect this harness, and then slide the window down into those clamps. Once you have it all the way in and clamped down, tighten up those two 10mm nuts, put your vehicle into accessory, plug in the switch, and just test out the regulator. You can see it works. You can just disconnect the switch and make sure you put your car back in the off position.
We'll fast forward as Mike replaces that water shield. To replace your door panel take the small panel and push it back onto these studs. Then, push the harness for that switch back up through the hole in the door panel. Line up the clips on the door panel, and once you have them all lined up, just hit them into place. Reconnect the switch and push it down into place, and then replace those two 7mm bolts and tighten them back up. Now just replace the small cover, and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Flat Blade Screwdriver
Putty Knife
7mm Socket
Painter's Tape
10mm Socket
Ratchet
1. Removing the Door Panel
Pry up the window switch panel with a flat blade screwdriver
Disconnect the door lock wiring harness
Disconnect the window switch wiring harnesses
Disconnect the mirror switch wiring harness
Disconnect the trunk switch wiring harness
Remove the two 10mm bolts inside the door pull
Pry out the door panel with a door panel clip tool or putty knife
Lift the door panel up and off
Remove the three 7mm bolts from the speaker
Disconnect the speaker wiring lead
Pull off the speaker from its clips with a flat blade screwdriver
Carefully peel off the water shield
2. Removing the Window Regulator
Disconnect the window motor lead
Loosen the two 10mm bolts that hold the window to the regulator
Raise the window by hand
Hold the window in place with painter's tape
Disconnect the window motor lead
Remove the three 10mm bolts from the regulator
Remove the two 10mm bolts from the window track
Pull the window regulator out through the door
3. Installing the New Window Regulator
Swap the two 10mm bolts to the new window regulator
Push the regulator into the door
Insert and tighten the four 10mm bolts into the regulator
Tighten the two 10mm bolts into the window track
Reset the window motor as described in Step 4
Remove the painter's tape from the window
Lower the window onto the regulator
Insert the two 10mm bolts that hold the window to the regulator
4. Resetting the Motor
Connect the window switch wiring harness
Connect the window motor to the lead
Turn the vehicle on
Run the motor up for 4 seconds
Disconnect the window switch wiring harness
5. Reinstalling the Door Panel
Put the water shield into place
Put the speaker into place
Insert the three 7mm bolts into the speaker
Connect the speaker wiring lead
Lift the door panel into place
Push in the door panel clips
Insert the two 10mm bolts inside the door pull
Connect the door lock wiring harness
Connect the mirror switch wiring harness
Connect the window switch wiring harnesses
Connect the trunk switch wiring harness
Push in the window switch panel
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the window regulator on this 2003 GMC Envoy XL. It's the same part and similar process on the regular GMC Envoy from 2002 to 2009. We show you on the driver's side, but the passenger's side is a similar procedure. The items you'll need for this include a new window regulator from 1AAuto.com, a flat blade screwdriver, a 7mm and 10mm socket and ratchet, and a putty knife.
Pry up the back of your switch panel with a flat blade screwdriver and then pry up the front. Then pull the switch panel up and out, push the tab on these two harnesses on this end, and disconnect them. Then use a flat blade screwdriver, and pry up the tab on the remaining harnesses.
Next, remove this 10mm bolt in here and this 10mm bolt right there. We'll fast-forward as Mike does this. Using a putty knife, just push this back in behind the door panel and slide it down until you find a clip. Then just pry out. Then you can reach your fingers back there and just pry out around the edge. Then just pry out on this small part of the panel up here and lift your door panel up and out of the window sill. Then it's free.
Now, you'll have to remove the speaker, so just remove these three 7mm bolts, and just push the tab on this harness and disconnect it. There's two clips on the back of the speaker. Pry out right here and then down here. Now remove your water shield. A razor blade helps because you can just cut the adhesive around here.
These are cable style regulators. This cable wraps through and all through these conduits. Usually what happens is that breaks, and then you can actually just grab onto your window and move it up or down, and you want to move to a position where you can get off this 10mm nut and then this one here in the front. You do just need to loosen them up. You don't need to remove them. Open up those clamps and then slide the window out of them and all the way up. Push the tab on this harness and disconnect it. Loosen these two 10mm bolts and then remove one, two, and three.
Now lift your regulator up so that it unhooks. Then just angle it down and out through here. On the left is the old window regulator; on the right is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same.
Swap those two 10mm bolts you used to hand the regulator over to your new window regulator. We'll just fast-forward as Mike does this. Take your new window regulator, feed it back into the door, and clip those two bolts into place. Once you have everything lined up, just replace the other bolts and tighten them up. Reconnect your harness.
Then take your switch panel and reconnect the harnesses for the window switches. Put your car into accessory, and just move the regulator down to where it was when you removed the other one. Now that you have access to both clamps, disconnect your switch panel and make sure you turn off your car. Loosen up the clamps on the regulator, then slide your window down into place. Make sure it's lined up and all the way down into those clamps, and then tighten the clamps back up.
We'll continue to fast-forward as Mike pushes those harnesses through the water shield and puts the water shield back into place. Line up your speaker and push it back into place. Then replace those three 7mm screws and tighten them up. Reconnect your speaker harness.
To replace your door panel, push the harnesses back through this hole. Then lift the door panel up and into the window sill. Once you have it lined up, push it down into place. Then make sure the clips are lined up, and then just hit them back in around the sides of the door panel. For these bolts, what you want to do is be able to hold them into the socket so a little bit of glue or any kind of piece of cloth. I just have a little electrical tape, put it on the bolt head, and stick into the socket. That way your screw will stay in there. Then you can just put it right in and start it. We'll just fast-forward as Mike replaces and tightens up those two bolts. Reconnect the harnesses to your switch pack. Then line up your switch panel and push it back down into place.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
WRA51162
In Stock
Product Reviews
Loading reviews
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
GMC is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by GMC or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.