★★★★★
January 27, 2025
1999 Explorer Suspension
Great quality parts. Fast shipping.
Replaces
About TRQ:
TRQ is a trusted brand dedicated to making every repair a success story by combining premium parts with easy installation. Each TRQ part is engineered by a team of automotive experts to meet or exceed OEM standards, delivering enhanced performance and maximum longevity. With rigorous in-house testing, the brand ensures superior fit and function across every product line. TRQ also provides customers with best-in-class, step-by-step installation videos—so you can complete repairs with confidence, whether you're a first-time DIYer or an industry professional.
Product Features
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This part fits 22 vehicles spanning 1998-2011.
| Year | Make | Model | Description |
|---|---|---|---|
| 1998-2001 | Ford | Explorer | Ford Explorer with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 1998-2000 | Ford | Ranger | Ford Ranger 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001-2005 | Ford | Ranger | Ford Ranger Edge Rear Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001-2005 | Ford | Ranger | Ford Ranger Edge 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001-2009 | Ford | Ranger | Ford Ranger XLT 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001-2003 | Ford | Ranger | Ford Ranger XL 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2004 | Ford | Ranger | Ford Ranger Tremor 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2005-2009 | Ford | Ranger | Ford Ranger XL 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2005-2009 | Ford | Ranger | Ford Ranger FX4 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2006-2009 | Ford | Ranger | Ford Ranger Sport Rear Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2006-2009 | Ford | Ranger | Ford Ranger Sport 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2010-2011 | Ford | Ranger | Ford Ranger 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 1999 | Mazda | B2500 Truck | Mazda B2500 Truck with 2 Piece Passenger Side Upper Control Arm Front with Front Torsion Bar Suspension 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001 | Mazda | B2500 Truck | Mazda B2500 Truck with 2 Piece Passenger Side Upper Control Arm Front with Front Torsion Bar Suspension 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 1999-2000 | Mazda | B3000 Truck | Mazda B3000 Truck Troy Lee with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001-2007 | Mazda | B3000 Truck | Mazda B3000 Truck DS with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 1998-2000 | Mazda | B4000 Truck | Mazda B4000 Truck 4 Wheel Drive with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2001-2003 | Mazda | B4000 Truck | Mazda B4000 Truck with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2004 | Mazda | B4000 Truck | Mazda B4000 Truck SE with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2004 | Mazda | B4000 Truck | Mazda B4000 Truck Base Model with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 2005-2009 | Mazda | B4000 Truck | Mazda B4000 Truck with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| 1998-2001 | Mercury | Mountaineer | Mercury Mountaineer with 2 Piece Passenger Side Upper Control Arm Front 12 Piece Steering & Suspension Kit TRQ PSA34488 |
| Brand Label | Part Number |
|---|---|
| Mevotech | CMS20403 |
| MOOG Chassis Products | K620319 |
| Ford | 2L2Z3078BA |
| Crumex | K8710T |
| Mevotech | GK8708T |
| NAPA Premium | 2605122 |
| ACDelco | 45D0090 |
| Ford | F5TZ3083A |
| Raybestos Chassis | 502-1021 |
| Ford | YL2Z3079AA |
| MOOG Chassis Products | CK8710T |
| Falcon Automotive | CA691 |
| Dorman - OE Solutions | 520-223 |
| Centric Parts | 623.65091 |
| DIY Solutions | SUS07319 |
| MOOG Chassis Products | CK8708T |
| Ford | 3L5Z3083AA |
| Centric Parts | 622.65036 |
| Mevotech | MK7275 |
| Ingalls Engineering | CAK8708T |
| Ford | 6L5Z5495AA |
| NAPA Premium | 2601464 |
| MOOG Chassis Products | K8708T |
| MOOG Chassis Products | K700542 |
| Mazda | 1F7035211 |
| Mevotech | MES3461 |
| Mevotech | MK8710T |
| Carquest | CA294B |
| NAPA Premium | 2605318 |
| MOOG Chassis Products | X8708T |
| Ford | F87Z3078EA |
| Ford | 6L5Z3078BA |
| TRW | JTC7003 |
| Precision Driveline | CB40083 |
| Ford | F77Z3078FA |
| Mevotech | MK8708T |
| Ford | 7L5Z3078A |
| MOOG Chassis Products | K8710T |
| Mevotech | GK8710T |
| Dorman - OE Solutions | 520-221 |
| DIY Solutions | SUS05041 |
| Falcon Steering Systems | FCA690 |
| ACDelco | 45D1021 |
| Ingalls Engineering | CAK8710T |
| SYD | K8708 |
| MOOG Chassis Products | X8710T |
| DIY Solutions | SUS05040 |
| Centric Parts | 623.65034 |
| MasterPro | 4CB40237 |
| Dorman - OE Solutions | 520-224 |
| Precision Driveline | CB40018 |
| MAS Industries | CB85153 |
| SYD | K8710 |
| Dorman | 535-110 |
| Centric Parts | 623.65033 |
| Precision Driveline | 3CB40018 |
| MasterPro | 3CB40238 |
| Centric Parts | 622.65059 |
| NAPA Premium | 2601464M |
| NAPA Premium | 2605317 |
| Mcquay-Norris | FA4054 |
| DIY Solutions | SUS05349 |
| Mcquay-Norris | FA4191 |
| Ford | F57Z3332AA |
| MOOG Chassis Products | RK8708 |
| Falcon Automotive | CA690 |
| Mevotech | CMS20402 |
| MOOG Chassis Products | EV317 |
| ACDelco | 45D3144 |
| Precision Driveline | 9CB40083 |
| MOOG Chassis Products | RK620319 |
| Ford | 6L2Z5K483AA |
| Ford | 1F703224X |
| DIY Solutions | SUS06607 |
| MOOG Chassis Products | RK620320 |
| Precision Driveline | CB40017 |
| Ford | 6L5Z3085AA |
| Dorman - OE Solutions | 520-299 |
| Dorman | 520-224 |
| NAPA | 260-5318 |
| NAPA | 260-5317 |
| Ingalls Engineering | CAK620320 |
| MOOG Chassis Products | CK620319 |
| Mevotech | MS20402 |
| MOOG Chassis Products | CK620320 |
| Motorcraft | MCS10720 |
| Motorcraft | MCSOE45 |
| Carquest | CA034B |
| MOOG Chassis Products | RK8710 |
| Ford | YL2Z3078AA |
| Mevotech | MS20403 |
| Centric Parts | 622.65035 |
| Mevotech | CMK8710T |
| ACDelco | 45D3143 |
| Ford | 6L5Z3079BA |
| Centric Parts | 623.65057 |
| Ford | 1F7034320 |
| Ford | 3L2Z5495AA |
| Mevotech | GS20403 |
| DIY Solutions | SUS05348 |
| Mcquay-Norris | FA4190 |
| Precision Driveline | 4CB40017 |
| Ford | 1F7034310 |
| SYD | F77A3079FA |
| Ford | 2L2Z3079BA |
| Mevotech | MEV317 |
| Motorcraft | MCSOE44 |
| Ford | 8L5Z3085L |
| Carquest | CA035B |
| Dorman | 520-223 |
| Motorcraft | MCSOE10 |
| Crumex | K8708T |
| MOOG Chassis Products | K620320 |
| Mcquay-Norris | FA2102 |
| Raybestos Chassis | 507-1144 |
| Mevotech | MK8834 |
| MOOG Chassis Products | K8834 |
| Ford | F77Z3079FA |
| Ford | 2L5Z3083AA |
| Carquest | CA295B |
| Ford | 7L5Z3079A |
| Mevotech | GS20402 |
| Raybestos Chassis | 507-1143 |
| MAS Industries | CB85154 |
| Mevotech | CMK8708T |
| Ford | F87Z3A130BA |
| SYD | F77A3078FA |
| Ingalls Engineering | CAK620319 |
| NAPA Premium | 2605122M |
| MAS Industries | CB8708 |
| Ford | F87Z3079EA |
| Precision Driveline | CB40082 |
| Ford | 2L2Z5K483BA |
| Falcon Steering Systems | FCA691 |
| MAS Industries | CB8710 |
| Ford | F7ZZ3082CA |
| DIY Solutions | SUS07318 |
| MOOG Chassis Products | ES3461 |
| QuickSteer | K7275 |
| EMPI | 88-1586-K |
| Dorman - Premium | CB85154PR |
| Dorman - Premium | CB8710PR |
| Dorman - Premium | CB85153PR |
| Dorman - Premium | CB8708PR |
| Hollander | 511-01056AR |
| Hollander | 512-01379R |
| Hollander | 511-01057AL |
| Hollander | 512-01380L |
| MOOG Chassis Products | K7275 |
| Mevotech Supreme | MEV317 |
| Mevotech Supreme | GK8708T |
| Mevotech Supreme | MS20402 |
| Mevotech Supreme | CMS20402 |
| Mevotech Supreme | GS20402 |
| Mevotech Supreme | MK8834 |
| Mevotech Supreme | CMK8708T |
| Mevotech Supreme | MS20403 |
| Mevotech Supreme | GK8710T |
| Mevotech Supreme | CMK8710T |
| Mevotech Supreme | GS20403 |
| Mevotech Supreme | MK7275 |
| Mevotech Supreme | CMS20403 |
| Mevotech Supreme | MK8710T |
| Mevotech Supreme | MK8708T |
| Mevotech Supreme | MES3461 |
| Ford | 1L2Z3K661AA |
This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to show you how to replace an outer tie rod on this 2003 Mercury Mountaineer. We show you on the passenger side, but the driver side is the same procedure. The items that you need for this is a new outer tie rod from 1AAuto.com, a 7mm, 19mm, and 21mm socket and ratchet, a piece of pipe for some extra leverage, two adjustable wrenches, a pair of pliers, a hammer, a tape measure, jack and jack stands, and a torque wrench.
Pry off the hub cap by using a flat blade screwdriver in the small slot on the side. Once you get it started, you can just pull out around the edges. If you don't have the benefit of air tools, you'll want to start with the vehicle on the ground, loosen the lug nuts, then raise and support the vehicle on jack stands. Remove the lug nuts, wheel, and tire the rest of the way.
There's a small indent on the inner tie rod. Put the tape measure there and measure out to the center of the grease fitting, which is 9-1/16" in this vehicle. Then, just bend off the legs on your cotter pin on the bolt. Then just pull the cotter pin out with a pair of pliers. Then, using a 19mm socket and ratchet, just remove this nut. Spray this nut with some penetrating oil, and then, using two adjustable wrenches, just separate it. Once it turns, it's loosened up, and you can hammer your wheel knuckle until you see the outer tie rod move. You can see it move right there.
Now you can pull it up and out of the knuckle and twist off the outer tie rod. Up top is the old outer tie rod, and below it is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same.
For lineup purposes, ideally what you want to do is be able to remove this without turning the inner tie rod. Our bolt or nut didn't come loose. That's not a big deal, but it does mean that we will need to take this and have it aligned because we did turn the inner tie rod a little bit, but we can still put it back together. We'll fast-forward as Mike twists on the new outer tie rod. Remove the nut and then line up the outer tie rod with the hole on the wheel knuckle. You may need to move the wheel knuckle around a bit until it goes down in place. Once you get it in, replace that nut and then just tighten it up. You want to tighten this to about 50 foot-pounds. Once it's fully tightened, make sure the hole lines up with the castle nut, and you may need to turn it a bit more so that it lines up, and then just push your cotter pin through and bend the tabs in opposite directions.
Tighten that nut back on to the outer tie rod using your two adjustable wrenches. Put in your new grease fitting and tighten it up with a 7mm socket and ratchet. Now, just add a few squirts of grease into the grease fitting. Replace your wheel, and then replace all the lug nuts and tighten them preliminarily. Then, you'd want to lower the vehicle and tighten them the rest of the way and torque these in a crossing pattern to 100 foot-pounds. Replace your hub cap, and we recommend you have your front alignment checked and adjusted if necessary.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
In this video, we're going to be working with our 2006 Ford Explorer. We're going to show you how to remove and replace your vehicle's sway bar link in the front. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles. If you need these parts for your car, you can follow the link down into the description over to 1AAuto.com. Here are the items you'll need for this repair.
Using a 19mm socket and a breaker bar, loosen the lug nuts on your tire. Raise and support your vehicle. We're doing this on a lift to make it easier to show you what's going on, but this job can be done at home on a jack and jack stands. Finish removing your lug nuts. You should be able to do this by hand at this point but you can use a ratchet if you need to. You can then remove your wheel and tire.
It may be a good idea to apply some penetrating oil to whatever parts you're going to be working with. Put a 17mm wrench on the nut on the top side of your sway bar link and brace it against the frame of the vehicle. You can then use a 16mm socket and ratchet on the bottom to loosen it. The sway bar link on these vehicles is essentially a series of bushing and washers with a sleeve all held together by one long bolt, as opposed to being a one-piece unit like some other vehicles.
You can see ours is pretty rough here, because there's usually not this much slack. That's actually what your bushing is supposed to look like on all four pieces, one on each side. You can see the old ones are worn down or cut there. It looks like they've actually fallen off over time. Once the nut's out, you can try to remove the bolt from the center of the sway bar link. This can be pretty difficult, so if it doesn't come out by hand, don't be afraid to get on there and give it a good hit with a hammer. The sway bar link will disassemble just like that when you pull it out, so just make sure you have all the old bushing material and all the old washers off of it.
Now you sort of need to build the sway bar link into the truck, so we'll start with a washer and then a bushing. We'll go up through the control arm, install a bushing with the tapered end down, followed by another washer, the sleeve, a washer with the cup end facing up, and a bushing with the tapered end facing up. We'll go through the sway bar, install another bushing. You may need to use a screw jack or floor jack to jack up the control arm to get enough slack on that bolt to install the sway bar link. Then install the washer and a nut and tighten your new hardware down. You'll want a 17mm wrench on the nut and a 16mm socket and ratchet on the bolt end. Just tighten that up until it compresses the bushings so you know that everything's nice and tight and there's no slop in there to make any noise when you go over bumps. Once that's down tight, you can lower the weight off of the screw jack or floor jack.
Reinstall the wheel and tire onto your hub. It's easiest to put a lug nut inside of the 19mm socket to start it onto the studs. Get all five of these down as tight as you can by hand, and then we'll torque the wheel once there's some weight on it. Lower the vehicle back down and put partial weight onto the wheel and tire. This means that you may have your jack or lift under the vehicle. Get the tire to touch and let the vehicle come down some without allowing it completely off of the lift or jack. Torque your lug nuts to 100 foot-pounds in a cross pattern.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20+ year's experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly that's going to save you time and money. Thank you and enjoy the video.
In this video we'll be replacing the tie rod on this '98 Explorer same as any '95 to '01 Explorer, Navajo, and Ranger, Mazda B Series pickup, and really this is a procedure that is similar for most cars.
Tools you'll need on the Explorer: jack and jack stands, 8mm, 13mm, 15mm, 19mm, which I forgot there, 21mm sockets and ratchet, pliers, a tie rod puller which is the right way to do it. You can use a hammer but you have to be careful. Loctite, a red or black marker, and two large adjustable wrenches.
So obviously you're going to want to jack up and secure your vehicle. You can just work a screwdriver in there to pry off your cap, and these are 19mm. If you don't have impact tools, loosen your lug nuts on the ground, then raise your vehicle and secure it with a jack stand, and then remove the lug nuts. Once the lug nuts are off just pull the tire right off, and there's four bolts that basically hold the brakes on. There's one here 13mm, and one up here, and those just hold the calipers to this big bracket. There's also a 15mm bolt here, and a 15mm bolt right up here. We're just going to speed through removing those four bolts, and you pull the caliper up and off and you can wire tie it up top and then that bracket comes off with the 15mm bolts, and we'll pick it up from there.
This bracket then comes right off, and your rotor comes right off. You're going to want to take off this dust shield and its 8mm bolts. Remove this cotter pin with a pair of pliers. Needle nose usually works best but usually the best thing to do is just grab hold and break off the pin on this side. It's a 21mm bolt, and actually give it a good tug. It does come easy. We'll put our puller on there. Now you could just use a big hammer and pound this through, but we want be very careful. If you go that route, you don't want to mushroom the end of this, and then it actually won't go through your steering knuckle. Now really this is using the tie rod ball joint puller is the best way, and you'll end up tightening this up good, and pretty soon it will pop. There it goes. A couple of big adjustable wrenches here. I'll fast forward a little here as I try and mess with it to try and get the best angle to both get a good pull on the wrenches and still be able to see it with the camera.
So that's off so now I'll lock this one onto here. The new tie rod does come with a new nut here so what I'm going to do is mark really well where this nut was so that when I put the new one on I know to go right up to where I put the red marks. I'm going to put just a little bit of Loctite on here, some down here, and put the new nut on. You can tell pretty well where it was. What you want to take into account is if either this nut or the length of your new tie rod is any different, you want to adjust the position of this nut. So if your tie rod is a little shorter, you adjust it out a little bit, or if the tie rod was a little longer than your original adjust it back in. So that's about where my old one was.
Now I'll put the new tie rod on, and you want to make sure you hold this. You don't want this twisting because that is adjustment as well, and if you do this this should give you a pretty good initial alignment. I recommend you go get an alignment so you don't wear out your tires too quickly or end up wearing out the new tie rod or wearing out your ball joints or anything like that if you car's not aligned correctly. Start my bolt down here to hold this in place. Now I want to tighten the lock nut up here really good. So I'm going to now tighten up this nut to about 75 foot pounds, and tighten it up a little more to get that and get my cotter pin right through there. The cotter pin you just take it and yank it right around. Then last but not least we'll put in our grease fitting and take our pliers and tighten that up. It comes pre-greased, but you can fill it up with grease, and now we can put everything back together.
We'll kind of fast forward putting that brake shield back up and tightening up those three 8 mm bolts. We'll also fly through putting the brakes back together and your wheel back on. A couple of notes, again, you probably would want to get a alignment after you've done any steering or suspension work like this, and then also just the first time you drive your car just be very careful. You've worked on the brakes. You've worked on the steering. So make sure your car is stopping before you go fast, and make sure that there is no looseness or anything in the steering before you road test it.
If you do want to see putting your brakes back together in regular motion, just check out our front brake video. We'll put the wheel back on. Put your lug nuts on. Get them snug then lower your car to the ground. Torque them up to 90 to 100 foot pounds. Replace your cap, and you're in business.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front sway bar link on this 2003 Mercury Mountaineer, same as any 2002 to 2005 Mountaineer, as well as Explorer. Our front passenger side is broken, so we show you how to get it out and replace it with a new one from 1A Auto. You'll need new sway bar link from 1AAuto.com, 16mm and 19mm socket and ratchet, a piece of pipe for some leverage, jack and jack stands and a torque wrench.
You'll want to remove your center cap. If you don't have the benefit of air tools, then loosen your lug nuts with the vehicle on the ground. Then raise both front wheels and support the car with jack stands and then remove the lug nuts and wheel the rest of the way. Now you can pull the wheel free.
This is the driver side, which is actually still together, so you would, if you're removing one that was still together, put a 15mm socket and ratchet on top and a 16mm wrench on the bottom, remove that top nut and then go from there. On ours, it's broken so I'm just filling, basically, the cavity with penetrating oil. This is pretty typical: it breaks off up top here and you saw where you just filled it up with penetrating oil and now we're just messing around with it. We locked some locking pliers onto it. That penetrating oil really helped the bolt start up and we've basically broken the plastic here. Now this plastic tube will slide off.
We're just going to use a hammer and chisel to remove the rest of the plastic. This, of course, is the worst case scenario, you just want to remove the plastic, you can use some locking pliers and then just remove the nut on the bottom or at least loosen it up as much as you can. Then just hammer this down and out.
Before installing it, just jack up the other side, just slightly. Now replace your sway link and the order it should go in is: washer, bushing, control arm, then bushing, washer, the tube, and another washer, and then the bushing, and then your sway bar, then another bushing, another washer, and then the nut. You just want to tighten that nut preliminarily,and then release the jack.
To tighten up the link, what you want to do is have the car back down on the ground, and now I have a jack supporting just the front suspension so that basically everything is level and the suspension is in its correct ride height. Then tighten up the link by holding the wrench on top and then turning the bottom. Tighten it up so that the bushings are all squeezed to about the diameter of the washers.
Replace your wheel, then replace all the lug nuts and tighten them preliminarily. Then you'd want to lower the vehicle and tighten them the rest of the way, then torque each of these in a crossing pattern to 100 foot-pounds. Now replace your hubcap. Just line it up and hit it back into place.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to show you how to replace an outer tie rod on this 2003 Mercury Mountaineer. We show you on the passenger side, but the driver side is the same procedure. The items that you need for this is a new outer tie rod from 1AAuto.com, a 7mm, 19mm, and 21mm socket and ratchet, a piece of pipe for some extra leverage, two adjustable wrenches, a pair of pliers, a hammer, a tape measure, jack and jack stands, and a torque wrench.
Pry off the hub cap by using a flat blade screwdriver in the small slot on the side. Once you get it started, you can just pull out around the edges. If you don't have the benefit of air tools, you'll want to start with the vehicle on the ground, loosen the lug nuts, then raise and support the vehicle on jack stands. Remove the lug nuts, wheel, and tire the rest of the way.
There's a small indent on the inner tie rod. Put the tape measure there and measure out to the center of the grease fitting, which is 9-1/16" in this vehicle. Then, just bend off the legs on your cotter pin on the bolt. Then just pull the cotter pin out with a pair of pliers. Then, using a 19mm socket and ratchet, just remove this nut. Spray this nut with some penetrating oil, and then, using two adjustable wrenches, just separate it. Once it turns, it's loosened up, and you can hammer your wheel knuckle until you see the outer tie rod move. You can see it move right there.
Now you can pull it up and out of the knuckle and twist off the outer tie rod. Up top is the old outer tie rod, and below it is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same.
For lineup purposes, ideally what you want to do is be able to remove this without turning the inner tie rod. Our bolt or nut didn't come loose. That's not a big deal, but it does mean that we will need to take this and have it aligned because we did turn the inner tie rod a little bit, but we can still put it back together. We'll fast-forward as Mike twists on the new outer tie rod. Remove the nut and then line up the outer tie rod with the hole on the wheel knuckle. You may need to move the wheel knuckle around a bit until it goes down in place. Once you get it in, replace that nut and then just tighten it up. You want to tighten this to about 50 foot-pounds. Once it's fully tightened, make sure the hole lines up with the castle nut, and you may need to turn it a bit more so that it lines up, and then just push your cotter pin through and bend the tabs in opposite directions.
Tighten that nut back on to the outer tie rod using your two adjustable wrenches. Put in your new grease fitting and tighten it up with a 7mm socket and ratchet. Now, just add a few squirts of grease into the grease fitting. Replace your wheel, and then replace all the lug nuts and tighten them preliminarily. Then, you'd want to lower the vehicle and tighten them the rest of the way and torque these in a crossing pattern to 100 foot-pounds. Replace your hub cap, and we recommend you have your front alignment checked and adjusted if necessary.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Great quality parts. Fast shipping.
PSA34488
