Ford Mazda Lincoln Mercury Front Driver & Passenger Side 2 Piece Control Arm with Ball Joint Set TRQ PSA62207

Hi, I'm Mike at 1A Auto. We've been selling auto parts for over 30 years.

Hi everyone, today we're going to be installing our rear lower control arm on our 2007 Mazda 6 sedan behind me, and this is the, the part, they call it the rear lower control arm in the front because there's two on this particular vehicle. So if you need this part or any part for your car, come on over to 1AAuto.com.

So we're going to start by removing the wheel. I have it partially on the ground so I can break the lug nut free. It's a 21mm socket, I got my half inch breaker bar. Alright, so now those are broken free and I could turn it by hand.

I'm going to raise my vehicle. I have a two post lift, if you have a floor jack and jack stands you do the same thing. So now with the car up in the air we're gonna remove the lug nuts, instead of my side. Perfect, it's frozen on there, and this happens quite often when you have an aluminum rim with a steel front end, obviously the steel and the aluminum, they oxidize together.

So I'm going to show you how to take this wheel off safely, a lot of people don't think about this, I know I didn't my first couple of times I did it. Take a lug nut and just put it back on by hand, not all the way, halfway, and now when you take your rubber mallet or your pry bar and you hit it from the other side, it doesn't fly off. I take a rubber mallet and I hit the rubber part of the tire, in the backside that came off nice and easy. Sometimes they, they don't wanna come off that easy and you just gotta keep giving it an effort back and forth. Now we can remove that lug nut and just mount the tire.

I'm gonna be removing the right lower control arm rear. The front has been removed for other processing, and the brakes have been taken off for another job, but while I'm here, I'm gonna remove the rear, and you'll be able to see better access with any other items removed. You don't need to remove the forward control arm or the brakes to do the rear lower control arm.

So now we're going to remove the nut from the knuckle for the rear rear control arm ball joint. It is a fifteen sixteenths or 24mm, I have a half inch ratchet on that, and you can see the movement from the CV shaft. So if I was to remove, if I was doing the job and I was doing both lower control arms, the front and the rear, I would have loosened up both these nuts at the same time before I dismounted the actual control up from this knuckle. Well, where I did that for a different show, and now I'm doing the rear, I just, you have to be careful from the movement if you don't want to pull that axle out of the joint.

Now I'm going to remove the rear would control arm ball joint from the knuckle, and I take the liberty to spray with a rust inhibitor spray, and I'm gonna use my pickle fork. I'm gonna go in right between the balls, right in the knuckle, make some noise here and see if I can separate them. That's how you do it, by the way, with that rear control arm ball joint.

Now, out, you can see both of these bushings, sometimes they will actually come out with pressed onto this sleeve on the stud of the ball joint, and when that happens you need to pull it off or press it off. I did the other side and I needed to use the press to press them off, a puller almost broke. So if that does happen, if you have a puller you can try it, be careful, safety glasses please. If you cannot get it off the actual outer ball joint, you have to go to a machine shop and get it pressed off.

To remove the rear lower control arm ball joint, the mounting bolt is right here, that's a 15mm head bolt, it's about four and a half inches long, goes into the subframe. The nut is welded in the frame, see, you have to worry about that, but to access that we have to lower the subframe. So first thing you're gonna do is get a bottle jack or another jack and support the subframe.

Now the pressure on it I can lower the, take the nut off where the body mouth goes to this subframe to the body, and I have to take this bracket down first. This is 15mm socket, and then we have another one right here, the large bolt. This nut is 18, I mean 21mm, sorry, 21mm nut. That one will be a little bit difficult breaking free. 21mm socket, I'm gonna break that free, let that bracket write down. The nut, note there's a washer, make sure you don't lose that.

Now we're gonna repeat these steps to bracket on the other side. 21mm nut, socket into 15. I'm gonna take this bracket down, and now the rear subframe will be free to pivot down so we can get to that money bolt for that control arm.

So there is a wire harness, it looks like it's for the O2 sensors, that is attached to this bracket. I'm just gonna leave it attached, a lot of hang freely, there's no need to undo that. I left the two front bolts attached to the subframe because I don't want, no need to take it all the way down.

I'm using a 15mm swivel, you can use a wrench, to break us free. Put it the control I'm in my hand, get that bolt out. I'm gonna use a little pry bar, and then I can pull this right out.

Here we have our two lower control arms for our oh seven Mazda 6. This one came from 1AAuto.com. They both the same length, same curvature. Comes with the factory style nut, which you need on this because of the spacer on the actual knuckle. Comes with pre-loaded threadlocker in it, and it has the shipping cover which goes over the dust boot to protect it during shipping. Make sure you discard that when you installing. Self greased joint with a nice locking ring clip.

High quality, can do this pot or any other part for your vehicle, come on over to 1AAuto.com.

To install the rear control arm, make sure you take the nut off first and the protective boot, we set those aside. And remember, when installing the stud for the lower ball joint, doesn't go up into the knuckle, it actually goes down into the knuckle. So this side could be installed wrong, goes in real nice but doesn't line up. You don't want to make that mistake because then you have done both the subframe again.

So we're gonna slide that right in. Now I can line my bolt up in, I have to get my pry bar again, little helping hand, line the threads up. Once I snug this down, I'm gonna get my torque wrench and I'm gonna torque it to the manufacturer's specs.

Before I put the subframe up, before I torque down this, the rear mounting of this control arm, I'm going to put it in the knuckle, because if it tightens that bushing up too tight and I can't move my control arm in place, that won't be good. You just gonna put the stud right through the hole there.

So I had to use my pry bar again to bring this subframe down so I could get my torque wrench in there. It's 93 foot-pounds to tighten this. You pry bar out.

I'm gonna mount this bracket back up, line up those two holes, make sure I put the washer on and the nut first just loosely so I can line these two bolts up. This is where I'm gonna actually lift up my subframe to line everything up again. Now the bolts will go right and smooth, find those up.

I'm going to repeat the process and the other side, put the bracket back up. I'm gonna torque this bolt to 114 foot-pounds, that's a 21mm socket. While I'm tightening that up and guiding my plastic, ma my plastic, sorry, my steel bracket, I just want to snug those bolts up. I do want to torque the body bolt, its body mount bolt, before I torque those down though.

Okay, now we're just going to repeat this process over here, the smaller bolts, 15mm socket, 76 foot-pounds.

Now we're ready to lower support, a bottle jack here, pull jack and we can get this out of the way.

So now I'm just going to remount my tire, thread up against the hub, put my lug nuts on hand tight. I'm just going to hand tighten them with my socket, then I'm gonna lower it down on the ground.

I'm going to torque these 83 foot-pounds. It's not going to torque my wheels at 83 foot-pounds in a star pattern, that just helps make sure that the seat of the rim is seated correctly against the hub. Check it, there you go.

Thanks for watching, visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.