Replaces
Replaces Ford Clutch & Brake Pedal Assembly Ford OEM F3TZ2455A
$353.95
Replaces 1992-96 Ford F150 F250 F350 F450 Rear Mounted Fuel Tank and Pump Kit TRQ FKA67530
$284.95
Replaces Ford Driver & Passenger Side 2 Piece Performance Tail Light Set TRQ Performance LTA71052
$146.95
Replaces Ford Driver & Passenger Side 2 Piece Performance Tail Light Set TRQ Performance LTA71051
$146.95
Replaces Ford Bronco F150 F250 F350 F450 Front Valance Panel DIY Solutions GRI00715
$125.95
Replaces Ford Bronco F150 F250 F350 F450 F53 Automatic Transmission Shift Lever Ford OEM F4TZ7210B
$113.95
Replaces Ford Front Driver & Passenger Side Power 2 Piece Power Window Motor & Regulator Assembly Set TRQ WRA50184
$104.95
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source from quality replacement parts and the best service on the internet. Hi, I'm Mike from 1AAuto. I hope this how-to video helps you out and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to service a taillight on this '96 Ford F150, pretty much the same as any '92-'96 F150, 250 and 350, as well as the '97 F250's and F350's. You probably just need a Phillips screwdriver. This truck has one of the screws that is a little bit rusty and stuck, so I have to use a couple of other tools that I show you.
These taillights are pretty straight forward repair. There are two Phillips screws on the outside and then there are two Phillips screws also right here on the inside. There and there. OK, we'll start with the inner ones first. Put the screwdriver in there. They can be a little rusty, so I'm just using a hammer. Hit the screwdriver a few times that usually breaks the screw loose. OK, one of these is rather tough, so this is actually an impact driver and what you do is you turn it to cock it, and then when you hit it, it both presses the tip in and turns it at the same time.
I'm just going to load that into the screw here, pushing against it and turning. OK. I hit it with the hammer and it comes loose. Worst case scenario, if you have a bolt on these that's really tough, if your taillight's broken, you can actually just break the taillight away and then the screw will come out. The other thing is, you can drill the head of the screw off and take the rest of the light out. It's coming out for me. Take those out. I just pull the light away. If you're just looking to change the bulb, these sockets twist counter-clockwise and come out. OK, the bulbs just pull right out of the socket, and back in; same thing down here. Push the other socket back in; new light from 1aauto, exactly the same as the old light. OK. So go right back on there. Just line up the sockets, get them in, twist to lock. Put this one in, twist to lock.
The taillight will go right back in place. What I'm going to do is, I'm going to push in, peek back, put your screws through and you can see back in there where the screw goes in, make sure it's lined up. Now I'm just going to start my outer screws in. I'm not going to tighten them up all the way yet. Push the light in. Just make sure the inner screws get lined up first. Start them in. OK. Then once you have them all started in, I just snug them all at first. Make sure the light is seated correctly and then tighten them up afterwards. When you tighten them up, just get them firm. You don't want tighten them up too much cause you can break the housing and break the light if you tighten them up too much.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free on 888-844-3393. We're the company that's here for you on the internet and in person.
