Replaces
Part Details
Specifications
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front sway bar bushings in the 2008 Dodge Ram 1500. Here are the items you'll need for this repair.
To replace the front sway bar bushings, you're going to undo these two brackets. Each one has two 15mm bolts. We're going to use the 15mm deep socket. You could also use a short socket and extension and a ratchet. The reason we're doing this job on the ground is because jacking it up and allowing the suspension to hang will put load on the sway bar, making it more difficult to line up these brackets and bolt them into place. Remove the bracket and repeat these steps on the opposite side. To remove the bushing from the bar, find where the bushings split from the factory. Our bushings here have either been glued together for some reason or just corroded, built up with gunk and stuck together over all the years they've been on this truck. We're going to use a razor blade to open up the factory slot that was in them. Remove them from the sway bar.
Here we have our old sway bar bushings that we removed from the vehicle and our new sway bar bushings from 1A Auto. You probably can't tell, but this is what these used to look like. See that they're all worn out. They’ve got some rust scaling in here. The rubber is corroding and falling apart. We've actually rubbed a hole completely through over here. It's not going to sit on our sway bar right and it's going to allow it to move up and down inside of this bore, which is going to create some noises and handling issues. This new sway bar bushing from 1A Auto, you could see is nice and round with nice thick rubber. It's going to fit our sway bar nice and tight and insulate it from any noise or vibration that we may have, especially from this. While this particular one is blue, they do come in a variety of colors just based on the manufacturing and what color rubber they decide to use. It's going to go on direct fit just like your original equipment and fix you up right.
We'll split the bushing and install it over our sway bar. This gap may not close fully. That's fine. The new bushings are much firmer than the old ones, obviously because the rubber is much thicker. It hasn't been worn away and deteriorated by chemicals and road grime. Line them up and reinstall the bracket onto the bushing. Start your two 15mm bolts. Do the same thing over here. Don't be afraid to tap that bracket on a little bit. Once both brackets are one and all four bolts have been started, go ahead and tighten them down with your 15mm socket and ratchet. Torque these bolts to 45 foot-pounds.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
PSA67736
