Replaces
Replaces Engine Oil Filter
$36.95
Interior Trim Removal Kit
$39.95
About TRQ:
TRQ is a trusted brand dedicated to making every repair a success story by combining premium parts with easy installation. Each TRQ part is engineered by a team of automotive experts to meet or exceed OEM standards, delivering enhanced performance and maximum longevity. With rigorous in-house testing, the brand ensures superior fit and function across every product line. TRQ also provides customers with best-in-class, step-by-step installation videos—so you can complete repairs with confidence, whether you're a first-time DIYer or an industry professional.
Returns: Parts with electrical components cannot be returned once installed.
Left Hand Drive:
All of our auto parts are intended for Left Hand Drive USDM vehicles. If your vehicle is Right Hand Drive, please ensure the part is correct for your specific vehicle.
Attention California Customers:
WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
This part fits 4 vehicles spanning 2003-2011.
| Year | Make | Model | Description |
|---|---|---|---|
| 2005-2010 | Chevrolet | Cobalt | Chevrolet Cobalt HVAC Blower Motor Assembly TRQ HMA84757 |
| 2006-2011 | Chevrolet | HHR | Chevrolet HHR HVAC Blower Motor Assembly TRQ HMA84757 |
| 2007-2009 | Pontiac | G5 | Pontiac G5 HVAC Blower Motor Assembly TRQ HMA84757 |
| 2003-2007 | Saturn | Ion | Saturn Ion HVAC Blower Motor Assembly TRQ HMA84757 |
| Brand Label | Part Number |
|---|---|
| Hollander | 615-00113 |
| Hollander | 615-00644 |
This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet. Hi I'm Mike from 1AAuto. I hope this how-to video helps you out and next time you need parts for your vehicle think of 1AAuto.com. Thanks.
In this video we're going to show you how to replace an AC and heater fan motor. Usually you'll start hearing the motor groan or make a higher pitched squeaking noise. That's when you know it's starting to get bad and sometimes they do just quit all together. The fan in this vehicle is actually molded into place. You do have to cut it out. The tools you'll need are a flat blade screwdriver, a utility knife, you'll need a drill with a half inch bit to drill out a couple of plastic rivets, a small socket ratchet, and eight small coarse thread bolts or screws. The lead goes in right above your passenger's feet, just use a screwdriver and press the tabs there and it comes right out. Then you get a nice sharp razor knife and you actually just cut. There's a groove all the way around the motor. You just push your razor knife right up into it.
Now I'm going to speed up the tape. Obviously you want to do this very carefully. Be very careful not to cut yourself with the razor knife. Like I said, there's a groove all the way around. Stick your razor knife up in there and just pull or push in a controlled manner and work your way all the way around the motor. There is a block in the front of the motor where the groove basically does not exist and that's the part where you try and cut into it that as much as possible and in the end probably a little piece of that will break off. The motor is held to this housing with two plastic rivets. I'm going to use the three-eighths drill. I'm going to speed up here. I just drilled those two plastic rivets. They're pretty easy. Don't use a lot of pressure; you don't want to drill too far through. Drill a little bit with the three eighths and then I actually do switch to a half-inch diameter drill bit to finish it off. Push down on the two studs where you removed the nuts and separate the plastic housing from the motor.
The old motor comes out. The new motor from 1A Auto, exactly the same as the old motor, put it obviously where the lead goes. That goes to the corresponding area on this housing. Put it down on. Speed up here again as I put those two nuts on and then tighten them up. You don't want to tighten them incredibly tight but you want them nice and firm. Now you need eight of these small coarse thread bolts. Basically you just use them. Place the rivets and molding. Fast forward here. As I just used, like I said, some small coarse thread bolts about the size of the diameter of the holes and bolt that together. You use them in place of where the rivets were, as well as you'll use a ring provided with the motor to reinstall it. Obviously we can't mold it back in so it comes with a ring. Put the ring in place and then use the small bolts to bolt it on to the plastic. You want to make sure your bolts aren't too long. You only want them to be a centimeter long, or so, or else they could interfere with the fan if they go too far through the housing.
I'm going to go through this kind of relatively fast. You've got the new motor with the ring on it. Put it up in there. Start a couple of the bolts in by hand as much as you can. Then get the two ones that are easiest to get to. Tighten them up somewhat and then you can tighten the third one that's more difficult to get to. Tighten that one up and then just reconnect the lead and you should be all set.
We hope this helps you out. Brought to you by www.1AAuto.com your source for quality replacement parts and the best service on the Internet.
Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the Internet and in person.
HMA84757
Perfect fit replacement for 2006 Chevrolet HHR. Followed video installation instructions from YouTube. I used the utility knife method to cut the old one out. It was super easy ( Use a fresh blade ). Plastic cut like butter. All of maybe a half hour from start to finish.
very easy to install with instructional video. awesome replacement part. make sure you have all the tools the video recommends.
Great price compared to the gm genuine. Fitment for the bolts were off a bit from the factory casing it sits in but was able to make it work easily.
A1 auto parts have been great and trustworthy. They back up there parts and give great customer service. They have a verity of parts and videos to help u when needed. I would highly recommend them for your automotive parts.
The Part worked out great perfect fit
Better than original! Make sure you gave the wright stuff before starting. You need a 7mm socket, 1/4in socket, and #8 5/8im screws. Super sharp utility knife too.
strong speed fan
Quick ordering. Great videos. Arrived in three days. Pain to remove old one but that's due to GM. Took about 45 minutes. I ended up using a hack saw blade which work better than the utility knife which I started with. New one bolted in perfectly. Thanks for including the 6 additional screws. Took about 20 minutes. No fan noise and lots of air flow. Didn't realize just how bad the old one had become before it just quit. Thanks A1 Auto.
There was some complications at first but gladly the costumer service team served me amazingly and fast, I'm extremely thankful. Happy car, happy daughter.
So the posts were a little off so after a little drilling to make it fit and has worked like a champ since. The last heater kept blowing the blower resistor and this new heater fixed the issue.
At this time we do not have the dimensions of these screws. We suggest searching a affiliated dealership website parts department that has these specifications.
