2009 Chevrolet Silverado 2500 HD WT Crew Cab Rear Passenger Side Interior Door Handle Repair Kit TRQ DHA49938

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace an interior door handle on this 2011 Chevy Silverado 1500. It's a similar process on the GMC Sierras and the Chevy Silverados from 2007 to 2012. The items that you'll need is an interior door handle replacement kit from 1AAuto, a flat blade screwdriver, a Phillips screwdriver, a 10mm socket and ratchet with extension, needle nose pliers, and a drill.

Using a flat blade screwdriver, you want to remove these three panels: the one behind the door handle, this door pull handle panel, and that triangular panel at the top there. Once those are removed, you'll see there are three 10mm bolts here. We'll just fast-forward as he removes those.

You just want to remove this little panel under this handle right here, so just pry that out with your flat blade. Now, you just want to remove these two 10mm bolts right here. You want to pry up that switch panel and just disconnect these harnesses. Just push in the tab on the top, and pull back on them. For this lead, there's a tab on the back of it. You just want to pry out that tab, and then the clip will actually pull up and out.

Now pull your lock up, and there's a little panel right here, just a little clip. You want to pry that out with the flat blade screwdriver. Once you pry that out, you can just lift that right up and off. Now you can start prying off the door panel. Just reach behind it and give it a sharp pull to release those clips. You want to do this all the way around the panel. Once you do that, you can just lift it off.

Then you want to tilt it. Now if you go in behind the door panel here, you'll see this door handle cable down here. Using needle nose pliers, just push the clip inward and you can pull that up and out.

This is an interior door handle kit from 1A Auto. You can see it even comes with the drill bit you need. All you have to do is supply the drill.

On the back side of your door panel, you'll see these plastic rivets. What you want to do is put that included drill bit into a drill, and just drill out these plastic rivets. Once you've removed all those rivets, you want to pry out this clip with a small flat blade screwdriver. Then this door handle bezel will come up and off.

On the other side of the door panel, where your door handle is, you want to pry out this little rubber pad here, and you'll see there's a small clip. You just want to pry that out with a flat blade screwdriver. and that small little piece right there will come right out. Then you just want to pull that door handle off and push that metal part through the door.

Now you want to put the new handle bezel down into place. Instead of plastic rivets, you're going to use superglue. You just want to put the washer into place, and then screw one of the included bolts down into place. You want to do this all the way around. This is what it should look like when you're finished.

Take the new door handle and push it into place. Make sure it snaps into place. Now, you want to make sure that these door panel clips line up in those holes, and that these hooks line up in these slots. Now, you want to take that door handle cable, put it back into its clip, pull back on it, and feed it into that little spot there.

Run all your harnesses up through where the door switch panel goes. You want to make sure that this lock tab goes up through the door panel. You want to line the door panel up on the windowsill, and then once its lined up, you can push in the clips all the way around. Take your lock, slide it back onto the tab there, and reapply that little square clip. We'll fast-forward as he replaces the two 10mm bolts under this handle here, as well as the 10mm bolt behind the door handle.

Now reconnect the harnesses to the door switch panel, and push it down into place. We'll continue to fast-forward as he replaces that pull handle and the two 10mm bolts that secure it. Now you just want to replace those four trim panels.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.