2005 Cadillac Escalade ESV Front & Rear 4 Piece Brake Rotor Set TRQ BRA13542

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the rear brakes on this 2002 Chevy Suburban. We show you on the passenger side, but the driver's side is the same procedure. The items you'll need are new brake pad and rotor kit from 1AAuto.com; 12, 18, and 22 mm socket and ratchet with a piece of pipe for extra leverage; flat blade screwdriver; large C-clamp; torque wrench; brake grease; brake cleaner; and jack and jack stands. Start off by loosening up these lug nut covers and we'll fast forward as Don does this. Once those are all loosened up, you can pull the hubcap free. You want to loosen the lug nuts preliminarily, raise the vehicle and remove them the rest of the way, unless you have air powered tools. Then, you can do it while it's up in the air.

To inspect your brakes, run your finger along the rotor, check for any deep grooves. You can look in here for the life of this brake pad and then through here for the life of the other brake pad. Remove these two 12mm bolts and we'll fast forward as Don does that. Use a large C-clamp. You put it on this end on the back of the caliper and on this brake pad and twist it in. This is going to push the caliper piston in and make it easier to pull the caliper up and off. Remove the large C-clamp, pull the caliper free, and set it aside. Pry up the brake pads.

Remove these two 18mm bolts and use a piece of pipe to help break it free. We'll fast forward as Don removes those two bolts. Pull your caliper bracket off. Pull the rotor off.

On the right is the old rotor and brake pads. On the left are the new ones from 1A Auto. You can see they're identical and they're going to fit exactly the same. Spray your rotor with some brake cleaner and wipe it down. Re-grease your caliper slides and apply brake grease to the tabs on either side of your brake pads.

Slide your new rotor into place and then twist on a lug nut to hold the rotor in place while you put the caliper bracket back on. Put your caliper bracket back into place and replace those two 18mm bolts and we'll fast forward as Don tightens those up. You want to torque these to about 85 foot-pounds.

To reset your caliper pistons, you want to put a brake pad in front of the pistons and twist the large C-clamp until it pushes the pistons in. Push your brake pads back into place and put your caliper back down into place and replace those two 12mm bolts. We'll fast forward as Don does this and tightens them up. You want to tighten these to about 30 foot-pounds.
Put your wheel back into place, and then, replace your lug nuts and tighten them preliminarily and we'll fast forward as Don does this. Lower the vehicle, and torque the lug nuts to 100 foot-pounds in a crossing pattern. Then, replace that hubcap and tighten up each of your lug nut covers.

Before taking the vehicle out on the road, you want to pump the brake pedal until it firms up, and then do a stopping test from five miles per hour, and then ten miles per hour and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front brakes on this 2005 GMC Savana 2500. It's a similar process on the Chevy Express. The items you'll need for this is a new break set from 1A Auto, 18mm, 21mm, 22mm socket and ratchet, a breaker bar and a piece of pipe for leverage, a flat blade screwdriver, penetrating oil, a hammer, large C-clamp, white grease, torque wrench, and jack and jack stands.

Start off by removing the wheel cover or whatever wheel trim you might have. This one has a chrome one. Pull that off, and then just use your socket and pull or loosen the lug nut covers. Pull the center cap off. If you don't have the benefit of air tools, you want to loosen the lug nuts with the vehicle on the ground, then jack up and secure the vehicle. Then remove the lug nuts, wheel, and tire.

Turn the wheel so that you can get to the brake. On the back of the caliper, there's two 18mm bolts. You just want to remove these. It can be a little difficult, so it helps to use a piece of pipe for extra leverage. We're just going to fast forward as he removes this.

The next step, you want to use a flat blade screwdriver to just pry the brake pads away from the caliper, and it will allow you to pry off that caliper. Just keep using the flat blade screwdriver, top and the bottom, you could see he's just going back and forth until, eventually, it will come off. You just want to set that aside.

Now, using the flat blade screwdriver, you just want to pry out your brake pads. Now on some vehicles, it's going to be more difficult than on others. It depends on the condition of the brakes. In this case, it takes just a little effort, and if you have to, you can use a hammer just be careful not to damage or bend anything. We're just going to fast-forward a little bit as he removes those brake pad slides.

There are two 21mm bolts back here that hold on this caliper bracket. Ours are a little rusted, so we spray them with some penetrating oil first, just to loosen them up and let that sit for a second. Then, using a breaker bar, and, actually, a piece of pipe for extra leverage, we just remove those bolts, and we're just fast-forwarding here as he does that. When you remove those bolts, the caliper bracket will come right off.

Now, you just want to take a hammer and hammer the back of that rotor. Just keep turning it and hammering the back of it, and it's going to come off. With the old rotor; the new rotor. New pads; same size. With this caliper guide, you can replace these boots . If they're torn, you pull them out and you push them in. The most important thing about the brakes here, what we found was the pedal was soft, it didn't feel like they should, and you'll notice that when these were sliding or weren't sliding and getting stuck on this corroded brake slide hardware, you know it's the new parts, allow the pad to slide just it should when they're new.

Now we're just cleaning up the new rotor real quick. What you want to do is you want to take some white grease and just put it on the clips of these new brake pads. Then, using a flat blade screwdriver, just scrape some of the corrosion on that caliper bracket. This will just help those slides to clip back on. Now, what you want to do is just clip those slides on, and as Don was saying: "They make a difference." New ones are definitely worth it and 1A Auto does sell these. This just clips right into place. We'll just push them down.

Now, what you want to do is just reset the pistons in this caliper. What you want to do is take one of your brake pads. If you're changing them, you want to use one of the old ones, and you want to lay it across these two pistons. Then, using a large C-clamp, as you tighten the clamp, that paddle push those pistons back in and reset them, as you can see here. Now they're reset.

Now we're just going to put on our brand new rotor, and once you get it into place, you just want to put one of those lug nuts on, and it will just hold it into place. We put the rest of the brakes together. Now you can put your caliper bracket back on, and, to place those bolts, you want to just do them first by hand. Then, once you get them lined up and both them in place, you can use a socket and ratchet to tighten them the rest of the way. Now you want to just torque those bolts to 100 foot-pounds.

Now you can put your brake pads back in. Now, for these caliper pens, what you want to do is you want to clean them off a little bit, and then put some white grease on them, this will help them so that they slide easier.

What you want to do, pull down your caliper and just fit it into place. Now you can see up here, you want that little gasket there to go in and you can slide your bolts back in. We'll fast-forward here as he tightens those up with a socket and ratchet. Torque these bolts to 100 foot-pounds. We're just going to fast-forward here as you remove that nut, put the wheel into place, and you just want to replace all those nuts and tighten them in a crossing pattern.

Again, if you don't have air tools, you just want to lower the vehicle and tighten those the rest of the way on the ground. Then you want to torque those lug nuts to 100 foot-pounds. Before actually driving the vehicle, you want to pump the brake until they're firm, and then you want to do a test, stopping from 5 mph then 10 mph.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the brake pads on this 2002 Chevy Suburban. The items you'll need for this include new brake pads from 1AAuto.com, a 22mm socket and ratchet with a piece of pipe for extra leverage, a T55 Torx bit, a large C-clamp, a torque wrench, jack and jack stands, and brake grease.

You want to just loosen up these 22mm caps, and then pull the hubcap free. Then you want to loosen these lug nuts while the vehicle's on the ground, then raise the vehicle and remove them the rest of the way, unless you have air powered tools, then you can do it while it's in the air, and then just remove the wheel. Check your rotors. If there's any deep grooves or rust you'll want to replace the rotors as well. You can also check your pad life. You can see ours are actually in good shape, but we're going to show you how to replace them anyways.

There's two T55 Torx bolts that you need to remove. We'll fast forward as we use a T55 Torx bit and a ratchet to remove those. Then, using a large C-clamp, just put it back behind the caliper here, and the other part right here on the brake pad, and just twist this in. This is going to push your caliper piston in and make it easier to pull the caliper off. Just remove the C-clamp and lift your caliper up and off and set it aside. Using a flat blade screwdriver, just pry out your brake pad. Sometimes the brake pads can be stuck in there. Use a flat blade screwdriver and a hammer to pry it free. Apply brake grease to the tabs on either side of your brake pads.

Push your new brake pads into place and use a hammer if necessary to lightly tap that into place. Using an old brake pad, just put it onto the caliper pistons and then tighten it in with your C-clamp, and this will just push those pistons in the rest of the way. Grease up your caliper bolts, put the caliper back into place, and slide those slide bolts back in. We'll just fast forward as Don tightens those up. You want to tighten these to about 30 foot-pounds. Now, replace your wheel and then replace those lug nuts and tighten them preliminarily. Lower the vehicle and tighten them the rest of the way. Now, torque the lug nuts in a crossing pattern to 100 foot-pounds. Replace the hub cap and tighten up those caps. After doing work on your brakes, you'll want to pump the brake pedal until it firms up and then try a stop test from five miles per hour and ten miles per hour, then you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.