Replaces
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you fog light replacement on this 2001 PT Cruiser, same as any 2001 to 2005. Tools you'll need are jack and jack stands, which is optional. What I mean by that is in this video, I do raise up the car and remove the tire. You don't necessarily have to do that. It does make it a lot easier. If you do jack it up, you'll want a tire iron or a 19 millimeter socket with ratchet and breaker bar to remove the wheel, 7 and 10 millimeter wrenches or sockets with ratchet, and then a flat blade screwdriver or needle nose pliers to pull out some little push pins that hold the inner fender in place.
You can see I have the car jacked up and the wheels off. You'll want to remove the little pin at the bottom. This is up near the bumper. Looking from the bottom of the car, there's a pin that holds the lower plastic panel at the bottom. Just use a screwdriver, or if you use a pair of needle nose pliers, put it up in there and pry that out. Now there are three 7 millimeter screws that you'll want to remove. We'll speed that up as we take out those 7 millimeter screws and then put that panel off to the side.
You'll want to apply some penetrating oil to the backs of the bolts on the fog light. If you're just looking at changing the fog light bulb, you turn it counter clockwise and then work it out of the socket. A lot like headlights, it just has a couple clips. I just work my thumbnail under the clips and then work the bulb out. Put that back on and just let it rest there for now.
Next, you're actually going to remove this lower horn 10 millimeter bolt. Now you can remove these 10 millimeter nuts that hold the light. You do just have to loosen these. Loosen this one up just a little bit more. There's a little tab that it sticks in right here. Push your fog light forward, and then up. Get a little rough with it and out.
We've put our nuts onto our new light. The new light from 1A Auto is nice and clear. Put the new light down. The fun part's just kind of getting this to fit in here. There's a tab there, and then there's a tab underneath. There's a tab here, tab underneath. Make sure those are in. Then, you can tighten it up. Plug it back in. Then put the front close panel back up into place and the three bolts that hold it. Also, I think I forget to film here, but there's also a push pin at the bottom that pushes in, and then tighten those up nice and snug.
Now, you'll want to put the wheel back on. Start your lug nuts all by hand first to avoid cross threading them. Then I use my impact wrench just to tighten them preliminarily. Then once the vehicle's back on the ground, I use a torque wrench to tighten the lug nuts to 100 foot pounds using a star pattern.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
