Replaces
Replaces Ram 2500 3500 Front Driver & Passenger Side 2 Piece Wheel Bearing & Hub Assembly Set Timken 1ASHS01610
$778.95
Replaces Ram 1500 1500 Classic 2500 3500 Driver & Passenger Side 2 Piece Mirror Set Trail Ridge TR00068
$499.95
Replaces 2011-18 Ram 3500 Truck Laramie Longhorn with Dual Rear Wheels (DRW) Rear Wheel Center Cap 2 Piece Set Mopar MPWHK00062
$494.95
Replaces Ram 1500 1500 Classic 2500 3500 Driver & Passenger Side 2 Piece Headlight Set Mopar MPLHP00003
$477.95
Replaces Dodge Ram 2500 3500 Ram 2500 3500 Front & Rear Semi-Metallic Brake Pad & Rotor Kit TRQ BKA23310
$474.95
Replaces Jeep Dodge Ram Chrysler Valve Body Solenoid Mopar 68353383AB
$469.95
Replaces Dodge Ram Front & Rear 4 Piece Performance Brake Rotor Set TRQ Performance BRA15172
$468.95
Replaces 2013-18 Ram 1500 2500 3500 Driver & Passenger Side 2 Piece Mirror Set Trail Ridge TR00043
$445.95
Replaces Dodge Ram 2500 3500 Ram 2500 3500 Front & Rear Ceramic Performance Brake Pad & Rotor Kit TRQ Performance BKA12907
$434.95
Part Details
Product Features
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
We'll open the door and right under the center of the dash is the lever. We'll pop the hood. Under the center of the hood, on the bottom, there's this lever. You want to move that and that will release the hood.
On this headlight there's two bolts in the front. There's one up here and then there's one straight down behind the grille, but we're actually going to start on the backside of the headlight. Down here, in the wheel well, there's a small cover that you have to remove and there's a push pin. That is the first thing you want to take out. We're going to use this thing, a push pin removal tool, but you can actually use a flat-tip screwdriver or a pair of pliers to get this. All right, with the push pin out of the way, this flap opens up. Having the wheel cut to one side actually gives you a little more space here to work.
At this point, you can reach into this little access panel and find the little lever that you push up, and you'll hear it snap all the way straight up and release this side of the headlight. Right down here, between the grille and the headlight, is another bolt and I'm just going to lift this up out-of-the-way so we can get a good camera shot out of it, but you don't actually have to move that. So now, I'm going to put a 10 millimeter socket on a swivel and a really long extension, I'd say it's at least 12 inches, and slide the ratchet all the way down here until it lands on the head of the bolt. The bolt itself is probably a good two inches long, so it takes a lot of turning to get it out. All right. When you feel like you've turned it about a thousand times, you're probably done.
So now, we can move on to this top one right here. It's, again, a 10 millimeter. So, we're going to lose the extension and the swivel, and just use that on the end of the quarter drive ratchet. Once you've cracked it loose, you can actually just get in there with your finger and turn it. There we go.
Now, you're going to want to remove the outer side of the headlight first, because there's actually a lip of the headlight that sits behind the grille on this side, so you can't just pull that headlight out. You have to remove it on this side, which requires a little bit of prying because there's a little ball on the back that snaps into place. So, hopefully we can wrestle this out. There we go, all right. Then you can slide that out.
On the back of the headlight, you can see this is the ball that was holding the headlight into place. That's the thing that took the effort to snap in and out. It locks right into this little channel right here. Up here, you can see this is the lever that you pushed up and down to lock the headlight in place or remove it.
All right, so, we're going to remove the high-beam connector, which we'll have to pull this white tab up like that to do, and then you push down the black tab and you can disconnect it. Then this thing slides right out like that. Over here, you have the red safety that you'll push up, and then you can remove the connector. At that point, your headlight is completely free of the truck.
All right, so to reinstall it, it is easy as reconnecting the connectors in the same way that you took them off. Make sure you push down your red pin. Put this back in place. Over here, you connect your high-beam connector and push the safety back in, and then you can push these two push pins back where they belong.
On the back side of the headlight you have this little ball that you need to snap into this hole, and then you have this, which needs to go into this hole where this tab is. But before you can do that, you have to put it in behind the grille. So, we'll get it in behind the grille, and then sort of feel the headlight around until it feels like the ball is setting in its little hole. Then, you can snap it into place.
So, we now need to get this bolt way down behind the grille. And obviously, if you just put it in here it's going to fall right out of the socket. So, here's a little trick. What you can do is you can take a piece of tape, put it on top of the bolt, and then you kind of jam the socket around it and that holds it. So, now you can hold it upside down. So, with that, then you just kind of slide it on down, and try and find the hole behind the grille. Might take a few tries, but this is the easiest way of doing it.
Before you tighten up that one all the way, you should always get all the other bolts in, and that way you can align them all first. That makes them easier to install. All right, with the top bolt in, now you can snug this one up, and then swap your ratchet to not have the extension or the swivel on it, and you can tighten this one up too.
On the back side of the light, we have to push that white lever back up, or actually back down. There we go. You'll feel it snap into place. Once that's done, you close your little access door and put your push pin back in. The procedure is exactly the same for the other side.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
In this video, we are going to be replacing a black headlight housings on this 2016 Ram 1500 pickup. If you need these parts for your vehicle, click the link in the description and head over to 1AAuto.com.
We're going to open the hood, right under the steering wheel. This little lever pops the hood. The hood's safety latch is right here. You’re going to pull it to the left. Pull up. There's a little door right here. We’re going to have to take this clip off. Use a trim tool. Get in behind, let our retainer up, pull it out a little, and then the clip will come off. Move this door out of the way.
You have the tire turned to the side. That makes it easier. Then in here, there's a little retainer. There's a little lock on the back here. It’s a little white tab. You're going to push it up, just like that. When the headlight is out, I will show you a little more detail of how you do it. You don't have to pull this shield off, but if you want to, there's some clips. You just use your clip tool to take it off, but we can get in there without taking that off.
There's a 10mm bolt right here. We’re going to take off with a 10mm socket and ratchet. Then there's another bolt that goes straight down here. You're going to need some extensions, so we're going to use our 10mm and an extension to get on that bolt. All right. I loosened that bolt up. All right. The bolt, I'm just going to leave that bolt down there for now. Everything is loose on this assembly. Grab underneath. You’re just going to have to pull it out real hard. There we go. I'm just going to use my socket and extension to loosen this bolt a little more. It seems like it's stuck in there. There we go, just pull it out.
To disconnect this connector, I'm going to pull on this little locker, and then we're going to push down on the tab and that pulls out. I'm going to use a small flat blade tool. Push this back. I'm going to push down on this lock. Slide it out and there it is. So this is how that lock works. When the headlights in there, this is locked down and there's a little tab that goes on the headlight through there. When it's in there, you want to push up and that will make that opening bigger, so the headlight assembly can come out.
This is our old headlight assembly. This is our new headlight assembly from 1A Auto. As you can see, it's an upgrade and it's a different look for the vehicle. You got instead of the chrome, you've got everything blacked out, so it will give you a more aggressive look. As you can see, the fitting areas are the same. On the back the adjusters the same, the connectors, the same connectors, all that's the same. The headlight assembly comes with new headlight bulbs and all the other marker bulbs and stuff. Get yours at 1A Auto, and you'll be ready to rock and roll.
We're going to reinstall the connectors. One goes there, and then you push the lock down. Then this connector goes right here, and you push that lock down. Then there's a couple little wire retainers that are going to get pushed into here. There's one over here that can get pushed in right there. We're going to push the headlight in this way first. Get this lined up and before you push it in. You're going to get the back lined up. When this is all set over here, you can put some pressure on the front of the headlight. Push it in. You're going to take the bolt, goes down in here. This happens to have a magnet in the socket, so it will hold the bolt. You could also use some grease or some electrical tape and tape it. Line that up.
Before I snug that lower bolt up, I'm going to install this bolt. Snug that up. I'll take our extension. Tighten this bolt up. It’s snug. Now I got to grab the lock, and I got to pull it down and that's locked. I can take this panel, stick it back on here, push it in, and push the push-pin in. All right.
Now we're going to check the headlight operation. Go through the lights, as you can see everything seems to be working, the blinker, the high beams, the markers. When you replace your headlights, you're going to want to adjust them. There's an adjuster right here, you can use a 7mm socket and extension. Get down in here and you can use a ratchet and if you tighten it, it goes up. If you loosen it, it goes down.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
